Ryobi TS1141 manual Squaring the Miter Table to the Fence, See Figures 18

Page 19

ASSEMBLY

Note: Many of the illustrations in this manual show only portions of the compound miter saw. This is intentional so that we can clearly show points being made in the illustra- tions. Never operate the saw without all guards securely in place and in good operating condition.

SQUARING THE MITER TABLE TO THE FENCE

See Figures 18 - 21.

Unplug the saw.

Push down on the saw arm and pull out the lock pin to release the saw arm.

Raise the saw arm.

Lift the miter lock lever.

Rotate the miter table until the pointer aligns with zero on the miter scale.

Push the miter lock lever down to lock the miter table.

Lay a square flat on the miter table. Place one leg of the square against the fence. Place the other leg of the square beside the throat plate in the miter table. The edge of the square and the throat plate in the miter table should be parallel as shown in figure 18.

If the edge of the square and the throat plate in the miter table are not parallel as shown in figures 19 and 20, adjustments are needed.

Using the blade wrench provided, loosen the socket head screws securing the fence. Adjust the fence left or right until the square and throat plate are parallel.

Retighten the screws securely and recheck the fence-to- table alignment.

MITER		MITER					Miter
MITER	Square	TABLE					lock
FENCE		TABLE					lock
FENCE							lever
							lever
	1	2	3	4	5	6	7

pointer throat plate

VIEW OF MITER TABLE SQUARE WITH FENCE

Fig. 18

MITER			MITER
FENCE			MITER
FENCE			TABLE
			TABLE
1	2	3	4	5	6	7

SQUARE

throat plate

VIEW OF MITER TABLE NOT SQUARE WITH

FENCE, ADJUSTMENTS ARE REQUIRED

Fig. 19

MITER			MITER
FENCE			MITER
FENCE			TABLE
			TABLE
1	2	3	4	5	6	7

SQUARE

throat plate

VIEW OF MITER TABLE NOT SQUARE WITH FENCE, ADJUSTMENTS ARE REQUIRED

Fig. 20

19

Image 19

Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsRead ALL Instructions General Safety Rules Never Start a Tool When ANY ROTATiNG COM Specific Safety RulesPonent is in Contact with the Workpiece Specific Safety Rules Symbol Signal Meaning SymbolsElectrical Connection Cord Length Wire Size A.W.GElectrical Double InsulationGlossary of Terms Work Clamp FeaturesProduct Specifications Blade WrenchBlade Wrench Storage Know Your Compound Miter SAWAMP Motor Bevel Lock KnobTools Needed Switch TriggerSpindle Lock Button Miter saw Head Blade Rear bracket Carrying handle Dust BAGScrews Rear bracket Carrying handle AssemblyInstalling the rear bracket/carrying handle UnpackingMounting Holes Mounting the miter saw base to the standBase Unpacking Indicator Bevel ScrewAssembling the miter saw head to the base See Figures 10Dust BAG INSTALLing Batteries in LaserWork Clamp To Leave Your Mark Aligning the laser guide lineRemoving Your Mark To Cut Your MarkSee Figures 16 To Install/replace the BladeSee Figures 18 Squaring the Miter Table to the FenceSee Figures 21 Squaring the Blade to the FenceSee Figures 25 Squaring the Blade to THE MITER TableSee Figures 29 OperationApplications To Cross cutSee Figures 31 IndicatorScaleSCREW indicator Bevel Cut Lock knob To Bevel CutSee Figures 33 To Compound Miter CutCompound Miter Cut Work Clamp Supports To Support Long Workpieces45 x 45 Compound Miter CUT Long WorkpieceCutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresPitch Number of Sides Right SIDE, Inside Corner Left SIDE, Outside Corner Cutting crown moldingLaying molding flat on the miter table Left SIDE, Inside Corner Right SIDE, Outside CornerSee Figures 37 Cutting warped materialWrong Bevel Pivot Adjustment AdjustmentsPositive Stop Adjustments Pivot Adjustments Travel Pivot AdjustmentTo adjust the miter lock lever To Adjust the Laser GuideLaser adjustment Screw Unlock Miter Lock Lever Lubrication MaintenanceGeneral Maintenance Brush ReplacementService Model NO. and Serial no