Ryobi TS1141 manual Cutting warped material, See Figures 37, Wrong

Page 28

OPERATION

	Bevel
	Angle		Type of Cut
	Setting

		Left side, inside corner
	33.85°	1.	Top edge of molding against fence
	33.85°	2.	Miter table set right 31.62°
		2.	Miter table set right 31.62°
		3.	Save left end of cut

		Right side, inside corner
	33.85°	1.	Bottom edge of molding against fence
	33.85°	2.	Miter table set left 31.62°
		2.	Miter table set left 31.62°
		3.	Save left end of cut

		Left side, outside corner
	33.85°	1.	Bottom edge of molding against fence
	33.85°	2.	Miter table set left 31.62°
		2.	Miter table set left 31.62°
		3.	Save right end of cut

		Right side, outside corner
	33.85°	1.	Top edge of molding against fence
	33.85°	2.	Miter table set right 31.62°
		2.	Miter table set right 31.62°
		3.	Save right end of cut

cutting warped material

See Figures 37 - 38.

When cutting warped material, always make sure it is posi- tioned on the miter table with the convex side against the fence as shown in figure 37.

If the warped material is positioned the wrong way as shown in figure 38, it will pinch the blade near the completion of the cut.

WARNING:

To avoid a kickback and to avoid serious personal injury, never position the concave edge of bowed or warped material against the fence.

Right

Fig. 37

WRONG	Fig. 38

28

Image 28

Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL Instructions Never Start a Tool When ANY ROTATiNG COM Specific Safety RulesPonent is in Contact with the Workpiece Specific Safety Rules Symbols Symbol Signal MeaningCord Length Wire Size A.W.G ElectricalDouble Insulation Electrical ConnectionGlossary of Terms Features Product SpecificationsBlade Wrench Work ClampKnow Your Compound Miter SAW AMP MotorBevel Lock Knob Blade Wrench StorageTools Needed Switch TriggerSpindle Lock Button Dust BAG Miter saw Head Blade Rear bracket Carrying handleAssembly Installing the rear bracket/carrying handleUnpacking Screws Rear bracket Carrying handleMounting Holes Mounting the miter saw base to the standBase Indicator Bevel Screw Assembling the miter saw head to the baseSee Figures 10 UnpackingDust BAG INSTALLing Batteries in LaserWork Clamp Aligning the laser guide line Removing Your MarkTo Cut Your Mark To Leave Your MarkTo Install/replace the Blade See Figures 16Squaring the Miter Table to the Fence See Figures 18Squaring the Blade to the Fence See Figures 21Squaring the Blade to THE MITER Table See Figures 25Operation ApplicationsTo Cross cut See Figures 29Indicator ScaleSCREW indicator Bevel Cut Lock knobTo Bevel Cut See Figures 31See Figures 33 To Compound Miter CutCompound Miter Cut Work Clamp To Support Long Workpieces 45 x 45 Compound Miter CUTLong Workpiece SupportsCutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresPitch Number of Sides Cutting crown molding Laying molding flat on the miter tableLeft SIDE, Inside Corner Right SIDE, Outside Corner Right SIDE, Inside Corner Left SIDE, Outside CornerSee Figures 37 Cutting warped materialWrong Adjustments Positive Stop AdjustmentsPivot Adjustments Travel Pivot Adjustment Bevel Pivot AdjustmentTo adjust the miter lock lever To Adjust the Laser GuideLaser adjustment Screw Unlock Miter Lock Lever Maintenance General MaintenanceBrush Replacement LubricationService Model NO. and Serial no