Ryobi TS1141 manual Features, Product Specifications, Blade Wrench, Work Clamp

Page 9

FEATURES

PRODUCT SPECIFICATIONS

Arbor	5/8 in.
Blade Diameter	7-1/4 in.
No Load Speed	5,800 r/min. (RPM)
Input	120 V, 60 Hz, AC only, 9 Amps

Cutting Capacity with Miter at 0°/Bevel 0°:

Maximum lumber sizes	1-1/2 in. x 4-1/4 in.
Cutting Capacity with Miter at 45°/Bevel 0°:
Maximum lumber sizes	1-1/2 in. x 3 in.
Cutting Capacity with Miter at 0°/Bevel 45°:
Maximum lumber sizes	1-1/2 in. x 3-1/2 in.
Cutting Capacity with Miter at 45°/Bevel 45°:
Maximum lumber sizes	1-1/2 in. x 3 in.

		Miter
		Lock lever
	“D” handle
	switch
	lock
	Upper
	Blade
	Guard
Dust BAG		Switch Trigger
		Switch Trigger
		Lower
		blade
		guard
		“NO HANDS ZONE”
Bevel	Bevel	BOUNDARY LINE
Bevel
Lock
Lock	Scale	“NO HANDS ZONE”
Knob	Scale
Knob
		LABEL
		Miter
miter		Scale
miter
fence		throat
		throat
		plate

BLADE

WRENCH

laser guide

bevel scale

base

MITER TABLE

WORK

CLAMP

Fig. 1

Image 9

Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsRead ALL Instructions General Safety RulesSpecific Safety Rules  Never Start a Tool When ANY ROTATiNG COMPonent is in Contact with the Workpiece Specific Safety Rules Symbol Signal Meaning SymbolsElectrical Cord Length Wire Size A.W.GDouble Insulation Electrical ConnectionGlossary of Terms Product Specifications FeaturesBlade Wrench Work ClampAMP Motor Know Your Compound Miter SAWBevel Lock Knob Blade Wrench StorageSwitch Trigger Tools NeededSpindle Lock Button Miter saw Head Blade Rear bracket Carrying handle Dust BAGInstalling the rear bracket/carrying handle AssemblyUnpacking Screws Rear bracket Carrying handleMounting the miter saw base to the stand Mounting HolesBase Assembling the miter saw head to the base Indicator Bevel ScrewSee Figures 10 UnpackingINSTALLing Batteries in Laser Dust BAGWork Clamp Removing Your Mark Aligning the laser guide lineTo Cut Your Mark To Leave Your MarkSee Figures 16 To Install/replace the BladeSee Figures 18 Squaring the Miter Table to the FenceSee Figures 21 Squaring the Blade to the FenceSee Figures 25 Squaring the Blade to THE MITER TableApplications OperationTo Cross cut See Figures 29ScaleSCREW indicator Bevel Cut Lock knob IndicatorTo Bevel Cut See Figures 31To Compound Miter Cut See Figures 33Compound Miter Cut Work Clamp 45 x 45 Compound Miter CUT To Support Long WorkpiecesLong Workpiece SupportsCOMPOUND-ANGLE Settings for Popular Structures Cutting Compound MitersPitch Number of Sides Laying molding flat on the miter table Cutting crown moldingLeft SIDE, Inside Corner Right SIDE, Outside Corner Right SIDE, Inside Corner Left SIDE, Outside CornerCutting warped material See Figures 37Wrong Positive Stop Adjustments AdjustmentsPivot Adjustments Travel Pivot Adjustment Bevel Pivot AdjustmentTo Adjust the Laser Guide To adjust the miter lock leverLaser adjustment Screw Unlock Miter Lock Lever General Maintenance MaintenanceBrush Replacement LubricationService Model NO. and Serial no