Bostitch manual Loading THE BTFP71917, Trigger­ Lockout Control, Trip Operation Mode

Page 8

LOADING THE BTFP71917

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

TO PREVENT ACCIDENTAL INJURIES:

Never place a hand or any other part of the body in nail discharge area of tool while the air supply is connected.

Never point the tool at anyone else.

Never engage in horseplay.

Never pull the trigger unless nose is directed at the work.

Always handle the tool with care.

Do not pull the trigger or depress the trip mechanism while loading the tool.

LOADING THE BTFP71917

1.Load nails through the slot in the rear of the magazine and past retaining clip.

2.Pull pusher back behind nail stick and release.

3.Ensure magazine pusher is behind the last nail stick.

TRIGGER­  LOCKOUT CONTROL

The trigger lockout control feature on BOSTITCH pneumatic tools provides a trigger lock feature for added safety control. Push the lockout control button in or out to activate or lock the tool trigger.

Trigger Lockout

Control Button

TRIP OPERATION MODE

Always disconnect air supply before making adjustments as accidental actuation may occur, possibly causing injury.

The BTFP71917 feature a selectable trigger system that allows the user to choose between the following modes of operation:

1. Contact Trip Operation

2. Sequential Trip Operation

-8-

Image 8
Contents OPERATION and MAINTENANCE MANUAL BTFP71917Index Limited Warranty U.S. and Canada OnlyIntroduction AIR Supply and Connections Definitions Safety GuidelinesSafety Instructions Maintaining the Tool Loading ToolOperation Tool Components Tool Specifications Fastener SpecificationsOperating Pressure Air ConsumptionFittings HosesSupply Source RegulatorTRIGGER­ LOCKOUT CONTROL Trip Operation ModeLoading THE BTFP71917 DIAL-A-DEPTHFASTENER Control Adjustment Selecting the Trip ModeContact Trip Sequential TripINSTALLING THE BELT HOOK Using the Integrated Pencil SharpenerTool Operation Before Handling or Operating this ToolContact Trip Operation Sequential Trip OperationBTFP71917 Jam Clearing Jam Clearing ProcedureTool Operation Check Replacement Parts Assembly Procedure for SealsAIR SUPPLY-PRESSURE and Volume Maintaining the Pneumatic ToolMaintenance Checklist Maintenance Benefit Procedure Service IntervalTroubleshooting Problem Cause CorrectionAvailable aCcessories Introducción ÍndiceNota Garantía Limitada Sólo EE.UU. y CanadáSuministro DE Aire Y Conexiones Pautas DE Seguridad / DefinicionesInstrucciones DE Seguridad Mantenimiento DE LA Herramienta Carga DE LA HerramientaFuncionamiento Componentes DE LA Herramienta Especificaciones DE LA Herramienta Especificaciones DE FijacionesPresión operativa Consumo de aireConectores ManguerasFuente DE Suministro ReguladorCarga de la herramienta Control DE Bloqueo DEL GatilloModo DE Funcionamiento DEL Disparador Ajuste DE Control DE Fijaciones DIAL-A-DEPTHDisparo DE Contacto Disparo SecuencialInstalación DEL Gancho Para EL Cinturón USO DEL Sacapuntas IntegradoFuncionamiento DE LA Herramienta Antes DE Manipular U Operar Esta HerramientaFuncionamiento DEL Disparo DE Contacto Funcionamiento DEL Disparo SecuencialDespeje de atascos en la BTFP71917 Procedimiento para despejar atascosRevisión Funcional DE LA Herramienta Presión Y Volumen DEL Suministro DE Aire Mantenimiento DE LA Herramienta NeumáticaPiezas DE Repuesto Procedimiento DE Ensamblaje Para LOS SellosLista de verificación de mantenimiento Mantenimiento Beneficio Procedimiento Intervalo De servicioSolución DE Problemas Problema Causa CorrecciónAccesorios disponibles Remarque Garantie Limitée É.-U. et Canada seulementAlimentation EN AIR ET Connexions Mesures DE Sécurité DéfinitionsInstructions DE Sécurité Entretien DE L’APPAREIL Chargement DE L’OUTILFonctionnement Composants DE L’OUTIL Spécifications DE L’OUTIL Caractéristiques DES AttachesPression de fonctionnement Consommation d’airAlimentation D’AIR ET Connexions Commande DE Blocage DE Gâchette Chargement de l’outilMode DE Déclenchement SÉLECTION/CHANGEMENT DU Mode DE DéclenchementDéclenchement SUR Contact Déclenchement SéquentielAjustement DE LA Commande D’ATTACHE DIAL-A-DEPTH Installation DU Crochet DE CeintureFonctionnement EN Mode Déclenchement SUR Contact Fonctionnement EN Mode Déclenchement SéquentielPour Utiliser LE TAILLE-CRAYON Intégré Fonctionnement de l’outilDégagement de blocage avec la BTFP71917 Procédure pour le dégagement des blocagesVérification DU Fonctionnement DE L’OUTIL Alimentation D’AIR-PRESSION ET Volume Entretien de l’outil pneumatiquePièces DE Rechange Procédure D’ASSEMBLAGE DES JointsEntretien Bienfait Procédure Intervalle De service Liste de vérification pour l’entretienProblème Cause Solution DépannageAccessoires disponibles