Hobart Welding Products DP 3035-20, DP 3035-10 manual Service, Support, Assistance

Page 31

Warranty Questions?

Call

1-800-332-3281

7 AM − 5 PM EST

Effective January 1, 2010

5/3/1 WARRANTY applies to all Hobart welding equipment, plasma cutters and spot welders with a serial number preface of MA or newer.

This limited warranty supersedes all previous Hobart warranties and is exclusive with

no other guarantees or warranties expressed or implied.

Hobart products are serviced by Hobart or Miller Authorized Service Agencies.

Service

You always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours.

Support

Need fast answers to the tough welding questions? Contact your distributor or call 1-800-332-3281. The expertise of the distributor and Hobart is there to help you, every step of the way.

Assistance

Visit the Hobart website: www.HobartWelders.com

LIMITED WARRANTY − Subject to the terms and conditions below, Hobart/Miller Electric Mfg. Co., Appleton, Wisconsin, warrants to its original retail purchaser that new Hobart equipment sold after the effective date of this limited warranty is free of defects in material and workmanship at the time it is shipped by Hobart. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

Within the warranty periods listed below, Hobart/Miller will repair or replace any warranted parts or components that fail due to such defects in material or workmanship. Hobart/Miller must be notified in writing within thirty (30) days of such defect or failure, at which time Hobart/Miller will provide instructions on the warranty claim procedures to be followed.

Hobart/Miller shall honor warranty claims on warranted equipment listed below in the event of such a failure within the warranty time periods. All warranty time periods start on the delivery date of the equipment to the original retail purchaser, and not to exceed one year after the equipment is shipped to a North American distributor or eighteen months after the equipment is shipped to an International distributor.

1.5 Years — Parts and Labor

*Original Main Power Rectifiers only to include SCRs, diodes, and discrete rectifier modules

*Reactors

*Stabilizers

*Transformers

2.3 Years — Parts and Labor

*Drive Systems

*Idle Module

*PC Boards

*Rotors, Stators and Brushes

*Solenoid Valves

*Spot Welder Transformer

*Switches and Controls

3.1 Year — Parts and Labor Unless Specified

(90 days for industrial use)

*Accessories

*Batteries (Trek 180 Only)

*Contactors

*Field Options

(NOTE: Field options are covered for the remaining warranty period of the product they are installed in, or for a minimum of one year — whichever is greater.)

*Flowgauge and Flowmeter Regulators (No Labor)

*HF Units

*MIG Guns/TIG Torches

*Motor-Driven Guns

*Plasma Cutting Torches

*Regulators

*Relays

*Remote Controls

*Replacement Parts (No labor) − 90 days

*Running Gear/Trailers

*Water Coolant Systems

4.Engines, batteries (except Trek 180) and tires are warranted separately by the manufacturer.

Hobart’s 5/3/1 Limited Warranty shall not apply to:

1.Consumable components; such as contact tips, cutting nozzles, contactors, brushes, relays, work station table tops and welding curtains, or parts that fail due to normal wear. (Exception: brushes and relays are covered on all engine-driven products.)

2.Items furnished by Hobart/Miller, but manufactured by others, such as engines or trade accessories. These items are covered by the manufacturer’s warranty, if any.

3.Equipment that has been modified by any party other than Hobart/Miller, or equipment that has been improperly installed, improperly operated or misused based upon industry standards, or equipment which has not had reasonable and necessary maintenance, or equipment which has been used for operation outside of the specifications for the equipment.

HOBART PRODUCTS ARE INTENDED FOR PURCHASE AND USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS TRAINED AND EXPERIENCED IN THE USE AND MAINTENANCE OF WELDING EQUIPMENT.

In the event of a warranty claim covered by this warranty, the exclusive remedies shall be, at Hobart’s/Miller’s option: (1) repair; or (2) replacement; or, where authorized in writing by Hobart/Miller in appropriate cases, (3) the reasonable cost of repair or replacement at an authorized Hobart/Miller service station; or (4) payment of or credit for the purchase price (less reasonable depreciation based upon actual use) upon return of the goods at customer’s risk and expense. Hobart’s/Miller’s option of repair or replacement will be F.O.B., Factory at Appleton, Wisconsin, or F.O.B. at a Hobart/Miller authorized service facility as determined by Hobart/Miller. Therefore no compensation or reimbursement for transportation costs of any kind will be allowed.

TO THE EXTENT PERMITTED BY LAW, THE REMEDIES PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE REMEDIES. IN NO EVENT SHALL HOBART/MILLER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF PROFIT), WHETHER BASED ON CONTRACT, TORT OR ANY OTHER LEGAL THEORY.

ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND

ANY IMPLIED WARRANTY, GUARANTY OR REPRESENTATION AS TO PERFORMANCE, AND ANY REMEDY FOR BREACH OF CONTRACT TORT OR ANY OTHER LEGAL THEORY WHICH, BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION, OPERATION OF LAW, CUSTOM OF TRADE OR COURSE OF DEALING, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, WITH RESPECT TO ANY AND ALL EQUIPMENT FURNISHED BY HOBART/MILLER IS EXCLUDED AND DISCLAIMED BY Hobart/Miller.

Some states in the U.S.A. do not allow limitations of how long an implied warranty lasts, or the exclusion of incidental, indirect, special or consequential damages, so the above limitation or exclusion may not apply to you. This warranty provides specific legal rights, and other rights may be available, but may vary from state to state.

In Canada, legislation in some provinces provides for certain additional warranties or remedies other than as stated herein, and to the extent that they may not be waived, the limitations and exclusions set out above may not apply. This Limited Warranty provides specific legal rights, and other rights may be available, but may vary from province to province.

hobart_warr 2010−01

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Description File Wire FeederOM-230 261C ProcessesProtect Your Investment From Hobart to YouTable of Contents Page HOT Parts can burn Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can injure Welding Wire can injureFire or Explosion hazard Falling Equipment can injureAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésLES Fumées ET LES GAZ peuvent être dangereux LES Pièces Chaudes peuvent provoquer des brûluresLE Soudage peut provoquer un incendie ou une explosion LA Chute DE L’ÉQUIPEMENT peut provoquer des blessures LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OULE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLes Pièces Mobiles peuvent causer des blessures LES Fils DE Soudage peuvent provoquer des blessuresInformations relatives aux CEM Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-230 261 Specifications − InstallationRemoving MIG Gun From Handler Spool Gun Connecting Spool Gun To HandlerMIG Gun Installing Wire Spool And Threading Welding Wire Controls − OperationSpool Gun MIG Gun Before maintaining − Maintenance & TroubleshootingRoutine Maintenance Disconnect powerChanging Drive Rolls Turn off and disconnect input powerChanging Lower Drive Roll Turn off TroubleshootingInput power Changing LinerBefore You Start Welding Gmaw MIG Aluminum Welding HintsWelding Techniques Contact Tube Position And Tip-To-Work Distance Common Problems/TroubleshootingCircuit Diagram − Electrical DiagramsOM-230 261 Complete Assembly − Parts ListOptional Page Page Page Support ServiceAssistance Hobart Welding Products Contact your Distributor for

DP 3035-10, DP 3035-20 specifications

Hobart Welding Products has established a reputation for manufacturing high-quality welding equipment, and their DP 3035-20 and DP 3035-10 models are prime examples of their innovative approach to welding technology. Designed to cater to a variety of welding needs, these products are engineered to enhance performance and provide durability in various industrial applications.

One of the main features of the Hobart DP 3035-20 and DP 3035-10 is their versatility. Both models are suitable for multiple welding processes, including MIG, TIG, and stick welding. This adaptability makes them ideal for fabricators, metalworkers, and DIY enthusiasts who require a reliable machine that can handle different types of materials and welding techniques. The machines are designed to work seamlessly with a range of metals, including steel, aluminum, and stainless steel, ensuring comprehensive usability across various projects.

Another remarkable aspect of these models is their advanced technology. Hobart incorporates cutting-edge inverter technology in both the DP 3035-20 and DP 3035-10, enabling these machines to deliver precise and consistent power output. This technology improves energy efficiency, reduces the overall weight of the welder, and enhances portability, making it easier for users to transport their equipment to job sites. Users can expect stable arc performance even at low amperage settings, further expanding their welding capabilities.

The user-friendly interface is another characteristic that sets the Hobart DP 3035 series apart. With clearly marked controls and a digital display, users can easily adjust settings for output and wire feed speed, facilitating an intuitive welding experience. Additionally, the process of switching between different welding modes is streamlined, allowing users to focus on their work without the hassle of complicated setups.

Durability is a priority for Hobart, and these welders are built to withstand the rigors of daily use. Featuring robust construction and high-grade components, the DP 3035-20 and DP 3035-10 are designed to provide long-lasting performance. They also come with built-in safety features such as thermal overload protection, ensuring reliable operation even under demanding conditions.

In conclusion, the Hobart Welding Products DP 3035-20 and DP 3035-10 models exemplify excellence in welding technology. With their versatile applications, advanced inverter technology, user-friendly design, and durable construction, these welders are well-equipped to meet the demands of modern welding tasks. Whether you are a professional tradesperson or a passionate hobbyist, these machines offer the reliability and performance that you need to achieve your welding goals.
Top Page Image Contents