Hobart Welding Products DP 3035-20 manual Fire or Explosion hazard, Falling Equipment can injure

Page 7

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near combustible surfaces.

DDo not install unit near flammables.

DDo not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.

FALLING EQUIPMENT can injure.

DUse lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.

DUse equipment of adequate capacity to lift and support unit.

DIf using lift forks to move unit, be sure forks are long enough to extend beyond opposite side of unit.

DKeep equipment (cables and cords) away from moving vehicles when working from an aerial location.

DFollow the guidelines in the Applications Manual for the Revised NIOSH Lifting Equation (Publication No. 94−110) when manu- ally lifting heavy parts or equipment.

MOVING PARTS can injure.

D Keep away from moving parts such as fans.

D Keep all doors, panels, covers, and guards closed and securely in place.

DHave only qualified persons remove doors, panels, covers, or guards for maintenance and troubleshooting as necessary.

DReinstall doors, panels, covers, or guards when maintenance is finished and before reconnecting input power.

READ INSTRUCTIONS.

DRead and follow all labels and the Owner’s Manual carefully before installing, operating, or servicing unit. Read the safety information at the beginning of the manual and in each section.

DUse only genuine replacement parts from the manufacturer.

DPerform maintenance and service according to the Owner’s Manuals, industry standards, and national, state, and local codes.

OVERUSE can cause OVERHEATING

DAllow cooling period; follow rated duty cycle.

DReduce current or reduce duty cycle before starting to weld again.

DDo not block or filter airflow to unit.

FLYING SPARKS can injure.

D Wear a face shield to protect eyes and face.

D Shape tungsten electrode only on grinder with proper guards in a safe location wearing proper face, hand, and body protection.

DSparks can cause fires — keep flammables away.

STATIC (ESD) can damage PC boards.

DPut on grounded wrist strap BEFORE handling

boards or parts.

D Use proper static-proof bags and boxes to store, move, or ship PC boards.

MOVING PARTS can injure.

DKeep away from moving parts.

DKeep away from pinch points such as drive rolls.

WELDING WIRE can injure.

DDo not press gun trigger until instructed to do so.

DDo not point gun toward any part of the body, other people, or any metal when threading welding wire.

H.F. RADIATION can cause interference.

DHigh-frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment.

DHave only qualified persons familiar with electronic equipment perform this installation.

DThe user is responsible for having a qualified electrician prompt- ly correct any interference problem resulting from the installa- tion.

DIf notified by the FCC about interference, stop using the equipment at once.

DHave the installation regularly checked and maintained.

DKeep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference.

ARC WELDING can cause interference.

DElectromagnetic energy can interfere with sensitive electronic equipment such as computers and computer-driven equipment such as robots.

DBe sure all equipment in the welding area is electromagnetically compatible.

DTo reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the floor.

DLocate welding operation 100 meters from any sensitive elec- tronic equipment.

DBe sure this welding machine is installed and grounded according to this manual.

DIf interference still occurs, the user must take extra measures such as moving the welding machine, using shielded cables, using line filters, or shielding the work area.

OM-230 261 Page 3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Description File Wire FeederOM-230 261C ProcessesProtect Your Investment From Hobart to YouTable of Contents Page HOT Parts can burn Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can injure Welding Wire can injureFire or Explosion hazard Falling Equipment can injureAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésLES Fumées ET LES GAZ peuvent être dangereux LES Pièces Chaudes peuvent provoquer des brûluresLE Soudage peut provoquer un incendie ou une explosion LA Chute DE L’ÉQUIPEMENT peut provoquer des blessures LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OULE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLes Pièces Mobiles peuvent causer des blessures LES Fils DE Soudage peuvent provoquer des blessuresInformations relatives aux CEM Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-230 261 Specifications − InstallationRemoving MIG Gun From Handler Spool Gun Connecting Spool Gun To HandlerMIG Gun Installing Wire Spool And Threading Welding Wire Controls − OperationSpool Gun MIG Gun Before maintaining − Maintenance & TroubleshootingRoutine Maintenance Disconnect powerChanging Drive Rolls Turn off and disconnect input powerChanging Lower Drive Roll Turn off TroubleshootingInput power Changing LinerBefore You Start Welding Gmaw MIG Aluminum Welding HintsWelding Techniques Contact Tube Position And Tip-To-Work Distance Common Problems/TroubleshootingCircuit Diagram − Electrical DiagramsOM-230 261 Complete Assembly − Parts ListOptional Page Page Page Support ServiceAssistance Hobart Welding Products Contact your Distributor for

DP 3035-10, DP 3035-20 specifications

Hobart Welding Products has established a reputation for manufacturing high-quality welding equipment, and their DP 3035-20 and DP 3035-10 models are prime examples of their innovative approach to welding technology. Designed to cater to a variety of welding needs, these products are engineered to enhance performance and provide durability in various industrial applications.

One of the main features of the Hobart DP 3035-20 and DP 3035-10 is their versatility. Both models are suitable for multiple welding processes, including MIG, TIG, and stick welding. This adaptability makes them ideal for fabricators, metalworkers, and DIY enthusiasts who require a reliable machine that can handle different types of materials and welding techniques. The machines are designed to work seamlessly with a range of metals, including steel, aluminum, and stainless steel, ensuring comprehensive usability across various projects.

Another remarkable aspect of these models is their advanced technology. Hobart incorporates cutting-edge inverter technology in both the DP 3035-20 and DP 3035-10, enabling these machines to deliver precise and consistent power output. This technology improves energy efficiency, reduces the overall weight of the welder, and enhances portability, making it easier for users to transport their equipment to job sites. Users can expect stable arc performance even at low amperage settings, further expanding their welding capabilities.

The user-friendly interface is another characteristic that sets the Hobart DP 3035 series apart. With clearly marked controls and a digital display, users can easily adjust settings for output and wire feed speed, facilitating an intuitive welding experience. Additionally, the process of switching between different welding modes is streamlined, allowing users to focus on their work without the hassle of complicated setups.

Durability is a priority for Hobart, and these welders are built to withstand the rigors of daily use. Featuring robust construction and high-grade components, the DP 3035-20 and DP 3035-10 are designed to provide long-lasting performance. They also come with built-in safety features such as thermal overload protection, ensuring reliable operation even under demanding conditions.

In conclusion, the Hobart Welding Products DP 3035-20 and DP 3035-10 models exemplify excellence in welding technology. With their versatile applications, advanced inverter technology, user-friendly design, and durable construction, these welders are well-equipped to meet the demands of modern welding tasks. Whether you are a professional tradesperson or a passionate hobbyist, these machines offer the reliability and performance that you need to achieve your welding goals.
Top Page Image Contents