Powermatic PM1300TX manual Operating the Machine, Maintenance

Page 13

Operating the Machine

Connect the dust collector to the power source. If power is flowing, a green indicator will light on the face of the control panel.

To operate the machine, use the buttons on the control panel, or use the provided remote control. To start the dust collector, press the ON button. If the remote control is used, aim it at the control panel. The machine will remain running until the OFF button is pressed. The digital readout will always display 00 while running.

The remote control operates on two AAA batteries. These will need replacing periodically.

NOTE: The infrared sensor on the dust collector has a 120° line-of-sight angle. See Figure 13. Outside of this angle, the remote control may not be effective.

Figure 13

Setting the Timer

While the machine is running, press the TIME button to activate the timer. Each time the button is pressed and released, the run time is incremented on the digital display by one minute and can be set up to 99 minutes.

If the TIME button is pressed and held, the time will scroll up to 99 minutes, then start again at

00.Release the button when the desired set time is reached. The dust collector will run for the amount of time displayed on the digital display. If you scroll past 99 and release the button at 10, for example, the machine will run for ten minutes, not 110 minutes.

If the OFF button is pressed while machine is running with the timer engaged, the machine turns off and the timer is disengaged; i.e., when the machine is restarted, the timer must be reset.

Connecting the Dust Collector to a Machine

Use the proper type hose to connect the dust collector to the machine being operated. Dryer vent hose is not acceptable for this purpose. Contact your nearest Powermatic distributor for a full line of Dust Collector hoses and accessories. You can customize your installation and obtain maximum performance with dust hoods, hoses, clamps, fittings, and blast gates.

Maintenance

Never perform maintenance on this machine before turning it OFF and removing plug from power source. Failure to comply may cause serious injury!

Cleaning the Filter Bag

Wearing a particle mask or respirator for protection against fine dust particles during cleaning is highly recommended.

During first use and after cleaning, the filter bag may allow some dust to escape. This is normal and will stop after a short period of time.

Clean both the filter and collector bags frequently to keep the collector's performance at its optimum. To clean:

1.Disconnect machine from the power source.

2.Unhook the filter bag from the hanger. Shake the bag so that the majority of the dust falls into the collector bag.

3.Loosen the retaining strap, and remove the filter bag from the housing.

4.Turn the bag inside-out and clean.

5.Turn the bag outside-in and re-attach to the housing using the retainer strap to secure.

Removing the Collector Bag

1.Disconnect machine from the power source.

2.Remove the collector bag by pushing the ring of the collector bag upwards and pulling the bag out at an angle.

3.Empty the contents into an appropriate container.

4.Turn the bag inside-out and clean.

5.Turn the bag outside-in and insert into the housing.

13

Image 13
Contents Part No. M-1791078 PowermaticWarranty Period Warranty and ServiceTable of Contents Page Page Introduction Specifications Unpacking Contents of Shipping CartonBase Machine Assembly Handles Cone InstallationFilter System Retainer strap connection Filter Bag System Assembly17mm wrench required Canister System AssemblyElectrical Connections Disconnect from power source unplugOverload Re-set Extension CordsOperating the Machine MaintenanceGrounding Instructions Cleaning the Canister FilterMotor Breakdown for PM1300TX Dust Collector Base Machine Replacement PartsIndex No. Part No Description Size Qty Parts List for PM1300TX Dust Collector Base MachinePM1300-BMHP Breakdown for PM1300TX Canister Filter System Parts List for PM1300TX Canister Filter System 1791077F Parts List for PM1300TX Filter Bag SystemElectrical Connections This page intentionally left blank This page intentionally left blank New Sanford Road LaVergne, Tennessee Phone Parte No. M-1791078 Ahora conPeríodo de la Garantía Garantía y Servicio TécnicoÍndice Page Guarde Estas Instrucciones Introducción Especificaciones Contenido del Embalaje de Transporte DesempaqueContenido de la Bolsa de Partes Figura Asamblea de cono y hardware FiguraMontaje de la Máquina Base Montaje del Cono ManijasSistema de Filtros Conexión de la Cinta de Retención Montaje del Sistema de Bolsa FiltroSe requiere una llave de 17mm Montaje del Sistema de CanastaReinicio por Sobrecarga Conexiones EléctricasCables de Extensión Para operar en 230 VoltiosMantenimiento Operación de la MáquinaLimpieza de los Filtros Canasta Instrucciones de Puesta a TierraDespieze del Colector de Polvo PM1300TX Máquina Base Partes de RepuestoNro. de Lista Parte Nro Descripción Tamaño Cantidad TS-1504021 Tornillo de Cabeza Hueca Despieze para el Sistema de Filtro Canasta PM1300TX Lista de Partes para el Sistema de Filtro Canasta PM1300TX Lista de Partes para el Sistema de Bolsa Filtro PM1300TX Conexiones Eléctricas Esta página dejada en blanco intencionadamente Esta página dejada en blanco intencionadamente New Sanford Road LaVergne, Tennessee Pièce N. M-1791078 Dépoussiéreur PM1300TXPériode de garantie Garantie et entretienTable des matières Page Retenez CES Instructions Numéros de stock Introduction SpécificationsContenu du conteneur dexpédition DéballageContenu du sac de matériel Figure Assemblée du cône et matériel FigureDispositif du socle Manches Cône InstallationSystème de filtre Connexion de la courroie de retenue Montage du système de sac-filtreClé de 17 mm requise Montage du système de boîte de filtrageRéglage de la surcharge Connexions électriquesRallonges Entretien Utilisation de la machineMoteur Instructions sur la mise à la massePanne du dépoussiéreur PM1300TX Machine de base Pièces de rechange’indice N de la pièce Description Taille Qté Liste de pièces du dépoussiéreur PM1300TX Machine de basePM2700-440 Large ruban non illustré Par pi PM2700-441 Page 1791087 Sac de collecteur en plastique Paquet de Liste de pièces du système de sac-filtre du modèle PM1300TX Connexions électriques Cette page est volontairement laissée vierge Cette page est volontairement laissée vierge New Sanford Road LaVergne, Tennessee Téléphone