Grizzly G1182HW instruction manual Adjustments, Table Gibs, Knives

Page 19

SECTION 5: ADJUSTMENTS

Disconnect power to the machine when perform- ing any maintenance, assembly or adjust- ments. Failure to do this may result in serious personal injury.

Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back.

Wear safety glasses during the entire adjust- ment process. Failure to comply may result in serious personal injury.

Table Gibs

Always lock the table with the table lock before using the jointer. If this step is not observed, the table could slide down while the jointer is operating. Serious personal injury may occur.

The function of the gibs are to allow precise adjustment of the table movement along the dovetail ways. Adjustment of the gib will dictate how easy it will be to move the tables up and down with the levers or handwheels. To adjust gibs:

1.Unscrew the upper and lower check nuts on the infeed table several turns, leaving the lock handle tight. See Figure 14.

2.With one hand securely on the lever bar, loosen the table lock handle and adjust the

G1182 6" Series Jointers

Setscrews

Lock Handle

Check Nuts

Figure 14. Location of check nuts.

upper and lower gib setscrews until table movement is smooth and controlled.

3.Once the gib has been properly adjusted, tighten check nuts and repeat Steps 1-2for the outfeed table.

4.Make sure there is no side-to-side movement of the tables once the check nuts have been tightened. If there is, repeat Steps 1-4.

Knives

These knives are extremely sharp. Never grab the cutterhead directly to rotate it. Always use the drive pulley. Always be sure the jointer is disconnected from its power source before you make any adjustments. Serious personal injury may occur.

KNIFE INSPECTION

The knives of your jointer must be periodically replaced or adjusted. Adjustments should be as precise as possible with tolerances within .002"-

.003" to prolong the sharpness of the knife edges. Improperly adjusted knives can unbalance the cutterhead and shorten bearing life, as well as produce substandard jointing or planing results. The knives are set at the factory using jack screws

-17-

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 47 HEAVY-DUTY Jointer Page G1182 Series Jointers Table Of Contents Safety Instructions For Power Tools SafetyLength AMP Rating Never Joint end grain Additional Safety Instructions For JointersGrounding Circuit Requirements110V Operation Extension CordsCommentary IntroductionPiece Inventory UnpackingG1182Z layout Site Considerations Clean UpBeginning Assembly AssemblyAttaching the motor G1182 6 Series Jointers Jointer to Stand Fence BeltBelt guard attachment Cutter Guard Belt GuardPedestal Switch Knife Setting GaugeTable Gibs AdjustmentsKnives Adjustments Using Jack Screws Outfeed Table Adjustments Using SpringsTable stop bolt and check nut Infeed TableLocation of stop bolt and stop tab Fence StopG1182 6 Series Jointers Test Run Stock Inspection OperationsFence position for bevel jointing G1182 6 Series Jointers Edge Joining BevelingRabbet Cuts Surface PlaningLubrication MaintenanceGeneral TablesClosure Machine Data Sheet Base Main TablesHEX NUT 3⁄ Stand for Jointer Model G1182Z & G1182ZHWStop TAB FenceCutterhead 308 Stand for Jointer Model G1182HWModel G1182HW & G1182ZHW Handwheel Assembly for423 414 420 424 418 422 419 416 421 417 Pedestal Mounted Switch for Jointer Model G1182ZXStand for Jointer Model G1182ZX Symptom Possible Cause Corrective Action TroubleshootingWarranty and Returns CUT Along Dotted Line Warranty CardGrizzly INDUSTRIAL, INC G1182 6 Series Jointers G1182 6 Series Jointers
Top Page Image Contents