Grizzly G1182HW instruction manual Outfeed Table, Adjustments Using Springs

Page 21

ADJUSTMENTS USING SPRINGS.

The knives are locked into the cutterhead with wedge- type gibs and gib bolts. Jack screws under the knives may be substituted with springs to help in the setting process. When using springs, it is advised that the jack screws be removed. To realign the knives:

1.Unplug the jointer!

2.Loosen the gib bolts until the knife is loose in the slot. The gib bolts turn clockwise to loosen and counterclockwise to tighten (when facing the head of the bolt). Remove the knife and jack screws. Place 1 spring in each of the two holes in bottom of the knife slot. See Figure 16A and 16B.

3.Place the knife setting gauge on the cutterhead as described previously, so the feet are securely planted on the cutterhead. Make sure the gauge extension rod is parallel to the cutterhead to main- tain accuracy.

4.The downward pressure provided by the gauge will set the knives at a uniform protrusion of approx- imately .070" above the cutterhead. The knife height should vary no more than .002"-.003" across the length of the cutterhead.

5.Maintain a constant pressure on the gauge while retightening the gib bolts.

6.Repeat the same procedure on the remaining knives. As mentioned before, the standard knife setting gauge is satisfactory for reasonably accu- rate knife setting tasks.

Knife

Spring

Gib Bolt

Gib

Figure 16A shows the location of the springs.

G1182 6" Series Jointers

Tighten

 

Loosen

Knife

 

Gib Bolt

Gib

Figure 16B. Tightening the gib bolts.

Outfeed Table

NOTICE

Model G1182HW uses handwheels for out-

feed and infeed table adjustments.

Facing the fence, the outfeed table is located to the left of the cutterhead. The outfeed table must be aligned to the highest point of the arc of the blades. If it is set too high, the board will hit the front edge of the table and be impossible to feed over the jointer. If the table is set too low, the back end of the board will fall into the cutterhead and snipe will occur.

1.Loosen the table stop bolt jam nut under the outfeed table. Turn the table stop bolt counter-clockwise several times so that it will not interfere when setting the correct table height. See Figure 17.

2.Rotate the cutterhead by turning the motor pulley. DO NOT grab the cutterhead itself. Bring one blade to the approximate apex of its arc.

3.Position a steel straightedge on the outfeed table. Extend the straightedge over the middle of the cutterhead. See Figure 18.

-19-

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 47 HEAVY-DUTY Jointer Page G1182 Series Jointers Table Of Contents Safety Instructions For Power Tools SafetyLength AMP Rating Never Joint end grain Additional Safety Instructions For Jointers110V Operation Circuit RequirementsExtension Cords GroundingCommentary IntroductionPiece Inventory UnpackingG1182Z layout Site Considerations Clean UpBeginning Assembly AssemblyAttaching the motor G1182 6 Series Jointers Jointer to Stand Fence BeltBelt guard attachment Cutter Guard Belt GuardPedestal Switch Knife Setting GaugeAdjustments Table GibsKnives Adjustments Using Jack Screws Outfeed Table Adjustments Using SpringsTable stop bolt and check nut Infeed TableLocation of stop bolt and stop tab Fence StopG1182 6 Series Jointers Test Run Stock Inspection OperationsFence position for bevel jointing G1182 6 Series Jointers Edge Joining BevelingRabbet Cuts Surface PlaningGeneral MaintenanceTables LubricationClosure Machine Data Sheet Base Main TablesHEX NUT 3⁄ Stand for Jointer Model G1182Z & G1182ZHWStop TAB FenceCutterhead 308 Stand for Jointer Model G1182HWModel G1182HW & G1182ZHW Handwheel Assembly for423 414 420 424 418 422 419 416 421 417 Pedestal Mounted Switch for Jointer Model G1182ZXStand for Jointer Model G1182ZX Symptom Possible Cause Corrective Action TroubleshootingWarranty and Returns CUT Along Dotted Line Warranty CardGrizzly INDUSTRIAL, INC G1182 6 Series Jointers G1182 6 Series Jointers
Top Page Image Contents