Installation Checklist

920-087-04

Inspect all components and accessories for damage before and after installation.

Remove the cardboard wall sleeve support and grille weatherboard.

Check for proper wall sleeve installation in accordance with the wall sleeve installation instructions.

Check for a subbase kit or other means of structural support which is required for ALL installations projecting more than 8" into room.

Install the recommended Condensate Drain Kits for complete condensate removal.

Ensure that the chassis is installed in a 16" high x 42" wide wall sleeve that is no deeper than 13 3/4". A bafﬂe kit is required if the sleeve exceeds that depth.

Ensure that drapes, bed, bedspread, furniture, etc. DO NOT block either return or discharge air grilles.

Inspect the condenser air inlet and outlet for any obstructions (shrubbery, etc.)

Ensure that 'reset' button is pressed on LCD device (only on cord connected models)

Section III – Chassis Installation

Check to be sure the wall sleeve, extension (if used), grille, and drain kit are installed properly before chassis installation.

1.Remove the weatherboard and center support from the sleeve (if still in place). Be sure an outdoor grille is attached.

Wall sleeve

Weatherboard

Center support

IMPORTANT: Use a wall sleeve adapter kit (PXSE) if installing a P-Series chassis in a T-Series sleeve.

Suffocation hazard

Keep bag away from babies and children.

Do NOT use in cribs, beds or playpens. Destroy immediately after opening. This bag is NOT a toy.

Failure to do so can result in personal injury and/or death

NOTE: To avoid breaking the door or hinge pins, do not apply excessive force when installing

2 Pins

Control

Door

Front Panel

3.Remove the two chassis shipping brackets from the ends of the shipping pallet.

Compressor

Chassis shipping bracket

Shipping pallet

2.Remove the front cover contained in a protective plastic bag from chassis. Remove the bag and dispose of it properly. If the control door is not installed, follow these steps:

•From the front of the cover, slide the right control door pin into the hole on the right side of the front cover. Slide the left door pin into the hole on the left side of the front cover opening and snap it into place.

IMPORTANT: When installing a Friedrich P-Series PTAC into an existing sleeve, it is important to ensure that the unit is installed completely. Inspection of the air seal between the condenser air bafﬂes and around the indoor mounting ﬂange is recommended. In some cases additional gaskets or bafﬂing may be required.

HEAT PUMPS specifications

Friedrich Heat Pumps are designed to provide efficient heating, cooling, and dehumidification solutions for various applications, including residential, commercial, and industrial settings. Renowned for their innovative technology and commitment to sustainability, Friedrich has become a recognized name in the HVAC industry.

One of the primary features of Friedrich Heat Pumps is their energy efficiency. These systems utilize advanced inverter technology, allowing the compressor to adjust its speed according to current heating or cooling demands. This leads to significant energy savings compared to traditional systems, which operate at a constant speed. By maintaining a more consistent indoor temperature, Friedrich Heat Pumps reduce energy consumption and lower utility bills.

In addition to energy efficiency, Friedrich offers a variety of models to suit different needs. The range includes air-source heat pumps, which extract heat from the outdoor air, and geothermal heat pumps, which utilize the stable temperatures found underground. This versatility allows users to select a system that best fits their specific climate conditions and application requirements.

Friedrich Heat Pumps also feature smart technology integration, making them a perfect choice for modern smart homes. Many models come equipped with Wi-Fi capabilities, allowing users to control their system remotely through a smartphone app. This feature not only enhances convenience but also allows for enhanced energy management, enabling users to monitor and adjust their heating and cooling schedules for optimal efficiency.

Another notable characteristic is their quiet operation. Friedrich Heat Pumps are engineered with noise-reducing features, making them suitable for residential areas where noise may be a concern. This focus on quiet performance ensures that users can enjoy a comfortable indoor environment without disruptive sound.

Durability and reliability are also key attributes of Friedrich Heat Pumps. Built with high-quality materials and rigorous testing processes, these systems are designed to withstand varying environmental conditions and provide long-lasting performance. Regular maintenance is further simplified with easy access to essential components, prolonging the system's lifespan.

In conclusion, Friedrich Heat Pumps stand out for their energy efficiency, innovative technologies, and superb performance characteristics. With options suitable for a wide array of applications, they are an excellent choice for anyone looking to enhance their indoor climate control while reducing their environmental footprint. Their advanced features, silent operation, and reliability make them a preferred option for modern heating and cooling solutions. Whether for residential or commercial use, Friedrich Heat Pumps offer a perfect blend of comfort, efficiency, and sustainability.