Friedrich HEAT PUMPS manual External Drain for new construction or unit replacement

Page 8

920-087-04

External Drain (for new construction or unit replacement)

When using an external drain system, the condensate is removed through either of two drain holes on the back of the wall sleeve. Select the drain hole which best meets your drainage situation and install the drain kit. Seal off the other with a cover plate.

Drain Tube Installation

1.Peel the backing tape off the gaskets and apply the sticky side to one cover plate and one mounting plate as shown in Details A and B.

2.Place the drain tube through the gasket and the mounting plate with the flange toward the wall sleeve.

3.Attach the drain tube assembly to one of the two drain holes at the rear of the wall sleeve. The large flange on the mounting plate is positioned at the bottom of the sleeve facing toward the sleeve, Detail B. When the drain tube is positioned at the desired angle, tighten the screws.

NOTE: If the wall sleeve has not been installed, the drain tube must be rotated to a horizontal position until after the sleeve is installed. Tighten the mounting plate screws when the tube is in the proper position. Make certain that the four overflow slots at the rear of the wall sleeve are not blocked. (See the drawing below.)

Cover Plate Installation

4.Mount the foam gasket to the cover plate. Using two #10 x 1/2" sheet metal screws (provided), attach the cover plate to the remaining drain hole. Make certain the large flange on the plate is positioned at the bottom of the sleeve.

5.Discard the additional cover plate, gasket, machine screws, and locknuts.

 

PXDR1O

QUANTITY

DESCRIPTION

 

 

2

COVER PLATES

1

MOUNTING PLATE

1

DRAIN TUBE

3

MOUNTING PLATE GASKETS

4

#10 X 1/2" MOUNTING SCREWS

2

10-24 X 1/2" MACH. SCREWS

2

LOCKNUTS

 

 

Figure 4

Drain Kit Installation

Foam gasket

Mounting plate

DETAIL A

Foam gasket

1/2" O.D. tube

Mounting plate

#10 sheet metal screws

DETAIL B

NOTES:

The large flange on the mounting plate is positioned at the bottom of the sleeve facing toward the sleeve. The drain tube must be rotated to a horizontal position to allow for the wall sleeve to be installed into the wall. Once the wall sleeve is installed, return the drain tube to a downward angle.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Ptac Table of Contents Model Number Code Ptac Installation Recommendations Building ElevationFriedrich Digital Control Features Digital TemperatureHeat Pump Mode Internal Drain optional for new construction Installation Instructions PXDR10 Drain KitDrain Kit Location and Installation External Drain for new construction or unit replacement Drain Tube InstallationCover Plate Installation Drain Kit InstallationWall Sleeve Installation Instructions Pdxws Typical Wall Sleeve InstallationDimensions Lintel InstallationWall Sleeve Extension Sealant Locations Section II Deep Wall Installation PxweExtension Installation Installation Instructions Model Pxga Standard Grille Standard GrillePower Cord Information 230/208V models only Electrical Rating Tables15/20A Lcdi Device 30A Lcdi DeviceInstallation Checklist Section III Chassis InstallationWall sleeve Wall sleeve flange Chassis flange and gasket Digital Control User Input Configuration Dip Switch SettingFactory Dip Switch Configuration Digital Control Operation Remote Thermostat Control board with optional Pdxrt escutcheon kit installedRemote Thermostat and Low Voltage Control Connections Fresh Air Vent Control Air Discharge GrilleDesk Control Terminals Auxiliary Fan ControlStart-up Checklist Appendix a Electrical Wiring for 265 Volt Models Line Voltage ConnectionsRoutine Maintenance ComponentsBasic Troubleshooting Techniques Environmental Effects Cooling ModeEnvironmental Effects Heating Mode Insufficient Maintenance and InspectionTest Mode Digital Control Diagnostics and Test ModeDiagnostics Friedrich Ptac Accessories Pxse Friedrich Air Conditioning Company 920-087-04

HEAT PUMPS specifications

Friedrich Heat Pumps are designed to provide efficient heating, cooling, and dehumidification solutions for various applications, including residential, commercial, and industrial settings. Renowned for their innovative technology and commitment to sustainability, Friedrich has become a recognized name in the HVAC industry.

One of the primary features of Friedrich Heat Pumps is their energy efficiency. These systems utilize advanced inverter technology, allowing the compressor to adjust its speed according to current heating or cooling demands. This leads to significant energy savings compared to traditional systems, which operate at a constant speed. By maintaining a more consistent indoor temperature, Friedrich Heat Pumps reduce energy consumption and lower utility bills.

In addition to energy efficiency, Friedrich offers a variety of models to suit different needs. The range includes air-source heat pumps, which extract heat from the outdoor air, and geothermal heat pumps, which utilize the stable temperatures found underground. This versatility allows users to select a system that best fits their specific climate conditions and application requirements.

Friedrich Heat Pumps also feature smart technology integration, making them a perfect choice for modern smart homes. Many models come equipped with Wi-Fi capabilities, allowing users to control their system remotely through a smartphone app. This feature not only enhances convenience but also allows for enhanced energy management, enabling users to monitor and adjust their heating and cooling schedules for optimal efficiency.

Another notable characteristic is their quiet operation. Friedrich Heat Pumps are engineered with noise-reducing features, making them suitable for residential areas where noise may be a concern. This focus on quiet performance ensures that users can enjoy a comfortable indoor environment without disruptive sound.

Durability and reliability are also key attributes of Friedrich Heat Pumps. Built with high-quality materials and rigorous testing processes, these systems are designed to withstand varying environmental conditions and provide long-lasting performance. Regular maintenance is further simplified with easy access to essential components, prolonging the system's lifespan.

In conclusion, Friedrich Heat Pumps stand out for their energy efficiency, innovative technologies, and superb performance characteristics. With options suitable for a wide array of applications, they are an excellent choice for anyone looking to enhance their indoor climate control while reducing their environmental footprint. Their advanced features, silent operation, and reliability make them a preferred option for modern heating and cooling solutions. Whether for residential or commercial use, Friedrich Heat Pumps offer a perfect blend of comfort, efficiency, and sustainability.
Top Page Image Contents