Powermatic 60C, 60HH Electrical Connections, Installing Fence Handwheel, Storing the Push Blocks

Page 12

Installing Fence Handwheel

Refer to Figure 12.

Install the handwheel (H) onto the shaft, and tighten the set screw with a 3mm hex wrench.

Knife Gauge Assembly (model 60C only)

Refer to Figure 13.

The knife gauge assembly consists of a bar, two end pieces and two e-clips. Slide the end pieces onto the ends of the bar as shown, and use a pliers to push the e-clips into the grooves on the bar.

Storing the Push Blocks

The two provided push blocks have a magnetic base – you can attach them to the jointer stand or any metallic surface, to keep them within easy reach.

Electrical Connections

Electrical connections must be made by a qualified electrician in compliance with all relevant codes. This machine must be properly grounded to help prevent electrical shock and possible fatal injury.

The Jointer is equipped with either a single phase, 230 volt motor; or a three phase, 230/460 volt motor.

The single phase unit is factory wired for 230 volts. You may either install a UL/CSA listed plug suitable for 230 volt operation, or “hard- wire” the jointer directly to a service panel. It is recommended that the single phase jointer be connected to a dedicated, minimum 20 amp circuit with a 20 amp circuit breaker or time delay fuse. Local codes take precedence over recommendations.

The three phase motor is pre-wired for 230 volt. It may be re-connected for 460 volts by changing the connections as illustrated in the diagram in the starter box (see “Converting from 230 Volt to 460 Volt”). You may either install a UL/CSA listed plug suitable for the specific voltage, or “hard-wire” the jointer directly to a service panel. It is recommended that the three phase jointer, when operated at 230 volts, be connected to a dedicated, minimum 20 amp circuit with a 20 amp circuit breaker or time delay fuse. When operated at 460 volts, connect the jointer to a dedicated, minimum 15 amp circuit with a 15 amp circuit breaker or time delay fuse. Local codes take precedence over recommendations.

Figure 12

Figure 13

(model 60C only)

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents WMH Tool GROUP, Inc Part No. M-1610084Warranty and Service More InformationTable of Contents Page Page Introduction Specifications 3HP 3PH 230/460V prewired60C Features and Terminology 60C and 60HH Jointers Contents of the Shipping Container UnpackingAssembly Tools required for assemblyAssembling Jointer to Stand Cutterhead GuardInstalling Drive Belt Aligning PulleysRemoving Guard Installing Belt Guard and Door Installing Switch ArmInstalling Dust Chute Hose and clamp not providedInstalling Fence Handwheel Knife Gauge Assembly model 60C onlyElectrical Connections Storing the Push BlocksGrounding Instructions 230V to 460V conversionAdjustments Installing and Adjusting KnivesExtension Cords Straight cutterhead only Replacing and Rotating Knife Inserts Helical Cutterhead OnlyLeveling Tables If table will still not line upAdjusting Depth of Cut Setting Outfeed TableRapid Adjust Fine AdjustExamples of incorrect settings Spring CuttingFence Movement Fence Stops See FigureDegree stop Degree forward stopOperating Controls Start/StopHand Placement Basic Jointer OperationJointing Short or Thin Work Direction of GrainJointing Warped Surfaces Edge JointingBeveling Skewing Shear Cutting Taper CutsMaintenance RabbetingCutterhead Maintenance Sharpening Knives model 60C onlyTable Removal Troubleshooting Mechanical and Electrical Problems TroubleProbable Cause Remedy Trouble Probable Cause Remedy Troubleshooting Operating Problems Straight cutterhead Replace nickedHelical cutterhead Rotate nicked Replacement Parts Parts List Base Assembly 60C and 60HHIndex No. Part No Description Size Qty TS-081B012 Base Assembly 60C and 60HH Parts List Fence Assembly 60C and 60HH Fence Assembly 60C and 60HH Parts List Straight Cutterhead Assembly 60C only Parts List Helical Cutterhead Assembly 60HH only Parts List Stand Assembly 60C and 60HH 60B-415MDC60C-439 Electrical Connections Single Phase, 230 Volt Electrical Connections 3 Phase, 230 Volt Electrical Connections 3 Phase, 460 Volt Page Vantage Drive Elgin, Illinois Phone
Related manuals
Manual 44 pages 25.26 Kb

60C, 60HH specifications

The Powermatic 60C and 60HH are two exceptional entries in the world of woodworking machinery, specifically designed for woodworkers who demand precision and efficiency in their operations. Both models embody Powermatic's commitment to innovation and performance, catering to the needs of professionals and serious hobbyists alike.

One of the standout features of the Powermatic 60C is its advanced digital readout (DRO) system. This technology provides users with accurate measurements and easy adjustments, ensuring that every cut is made with precision. The system helps eliminate guesswork, allowing woodworkers to focus on their craft without worrying about the accuracy of their settings. The 60C also features a powerful 1.75 HP motor, which is capable of handling even the toughest hardwoods with ease.

On the other hand, the Powermatic 60HH boasts the Helical Cutterhead technology, which offers a significant upgrade over traditional straight knives. The helical design consists of multiple cutting edges that provide a smoother cut and reduce tear-out, resulting in a superior finish. This is especially beneficial when working with figured woods or delicate materials. The 60HH also features a 3 HP motor, providing ample power for demanding applications and ensuring consistent performance even under heavy loads.

Both models are equipped with a rigid and robust cast-iron construction, ensuring stability and reducing vibration during operation. This design enhances the durability of the machines and extends their lifespan, making them a worthwhile investment for any serious woodshop.

The jointer beds are precision-ground and provide excellent support for long workpieces, while the fence is easily adjustable and provides accurate guidance for various operations, such as jointing and planing. The intuitive controls make it easy for users to switch between different functions and settings, enhancing workflow efficiency.

In terms of mobility, both the 60C and 60HH come with sturdy, adjustable legs and can be fitted with mobility kits that allow for easy movement around the workshop. This flexibility is a significant advantage for woodworkers who need to optimize their workspace.

In summary, the Powermatic 60C and 60HH represent the pinnacle of jointer and planer technology. With their innovative features, powerful motors, and user-friendly designs, these machines deliver unparalleled performance, making them invaluable assets in any woodworking shop. Whether you prioritize precise adjustments with the 60C or superior cutting capabilities with the 60HH, both models stand ready to elevate your woodworking projects to new heights.
Top Page Image Contents