Powermatic 60HH operating instructions Sharpening Knives model 60C only, Cutterhead Maintenance

Page 26

Sharpening Knives (model 60C only)

Knives should be kept sharp. This will contribute to better stock finish, longer machine life, and safer operation.

A jointer knife hone provides a simple way to sharpen straight knives. Hones are available from many woodworking supply stores. Carefully read any instructions that accompany the hone.

Use caution and proceed slowly when sharpening knives. Disconnect jointer from power source, and wear approved eye protection.

When finished sharpening knives, they should be re-set level to the outfeed table. See the “Installing and Adjusting Knives” section in this manual.

Knives can usually be whetted several times in the cutterhead before having to be removed and re-ground.

TIP: If the jointer is used frequently, keeping a spare set of knives on hand is recommended. Extra knives (stock no. 6296046, set of 3) may be obtained from your Powermatic distributor, or by calling WMH Tool Group at 1-800-274-6848.

Cutterhead Maintenance

The entire cutterhead assembly may be removed for bearing replacement or other maintenance procedures.

1.Disconnect jointer from power source.

2.Remove fence assembly from jointer (see Figure 36 and accompanying instructions).

3.Loosen motor mounting and push up on motor to create slack in belt (see page 10)

4.Remove drive belt from cutterhead pulley.

5.Lower both infeed and outfeed tables.

6.Loosen the two socket head cap screws on the fence support and pivot the fence support out of the way (see Figure 38).

7.Remove rabbeting ledge by loosening the two hex cap screws and washers (A, Figure 39).

8.Loosen the two bolts (B, Figure 39) that secure the cutterhead to the bed – these are accessed from the underside of the bearing blocks.

Either remove the knives or knife inserts from the cutterhead, or wrap cloths around it to prevent injury.

26

Figure 38

Figure 39

Page 25 Page 27
Image 26
Page 25 Page 27
Contents WMH Tool GROUP, Inc Part No. M-1610084Warranty and Service More InformationTable of Contents Page Page 60C Introduction Specifications3HP 3PH 230/460V prewired Features and Terminology 60C and 60HH Jointers Contents of the Shipping Container UnpackingAssembling Jointer to Stand AssemblyTools required for assembly Cutterhead GuardRemoving Guard Installing Drive BeltAligning Pulleys Installing Dust Chute Installing Belt Guard and DoorInstalling Switch Arm Hose and clamp not providedElectrical Connections Installing Fence HandwheelKnife Gauge Assembly model 60C only Storing the Push BlocksGrounding Instructions 230V to 460V conversionExtension Cords AdjustmentsInstalling and Adjusting Knives Straight cutterhead only Replacing and Rotating Knife Inserts Helical Cutterhead OnlyLeveling Tables If table will still not line upRapid Adjust Adjusting Depth of CutSetting Outfeed Table Fine AdjustFence Movement Examples of incorrect settingsSpring Cutting Degree stop Fence StopsSee Figure Degree forward stopOperating Controls Start/StopJointing Short or Thin Work Hand PlacementBasic Jointer Operation Direction of GrainBeveling Jointing Warped SurfacesEdge Jointing Skewing Shear Cutting Taper CutsMaintenance RabbetingCutterhead Maintenance Sharpening Knives model 60C onlyTable Removal Probable Cause Remedy Troubleshooting Mechanical and Electrical ProblemsTrouble Trouble Probable Cause Remedy Helical cutterhead Rotate nicked Troubleshooting Operating ProblemsStraight cutterhead Replace nicked Index No. Part No Description Size Qty Replacement PartsParts List Base Assembly 60C and 60HH TS-081B012 Base Assembly 60C and 60HH Parts List Fence Assembly 60C and 60HH Fence Assembly 60C and 60HH Parts List Straight Cutterhead Assembly 60C only Parts List Helical Cutterhead Assembly 60HH only Parts List Stand Assembly 60C and 60HH 60B-415MDC60C-439 Electrical Connections Single Phase, 230 Volt Electrical Connections 3 Phase, 230 Volt Electrical Connections 3 Phase, 460 Volt Page Vantage Drive Elgin, Illinois Phone
Related manuals
Manual 44 pages 25.26 Kb

60C, 60HH specifications

The Powermatic 60C and 60HH are two exceptional entries in the world of woodworking machinery, specifically designed for woodworkers who demand precision and efficiency in their operations. Both models embody Powermatic's commitment to innovation and performance, catering to the needs of professionals and serious hobbyists alike.

One of the standout features of the Powermatic 60C is its advanced digital readout (DRO) system. This technology provides users with accurate measurements and easy adjustments, ensuring that every cut is made with precision. The system helps eliminate guesswork, allowing woodworkers to focus on their craft without worrying about the accuracy of their settings. The 60C also features a powerful 1.75 HP motor, which is capable of handling even the toughest hardwoods with ease.

On the other hand, the Powermatic 60HH boasts the Helical Cutterhead technology, which offers a significant upgrade over traditional straight knives. The helical design consists of multiple cutting edges that provide a smoother cut and reduce tear-out, resulting in a superior finish. This is especially beneficial when working with figured woods or delicate materials. The 60HH also features a 3 HP motor, providing ample power for demanding applications and ensuring consistent performance even under heavy loads.

Both models are equipped with a rigid and robust cast-iron construction, ensuring stability and reducing vibration during operation. This design enhances the durability of the machines and extends their lifespan, making them a worthwhile investment for any serious woodshop.

The jointer beds are precision-ground and provide excellent support for long workpieces, while the fence is easily adjustable and provides accurate guidance for various operations, such as jointing and planing. The intuitive controls make it easy for users to switch between different functions and settings, enhancing workflow efficiency.

In terms of mobility, both the 60C and 60HH come with sturdy, adjustable legs and can be fitted with mobility kits that allow for easy movement around the workshop. This flexibility is a significant advantage for woodworkers who need to optimize their workspace.

In summary, the Powermatic 60C and 60HH represent the pinnacle of jointer and planer technology. With their innovative features, powerful motors, and user-friendly designs, these machines deliver unparalleled performance, making them invaluable assets in any woodworking shop. Whether you prioritize precise adjustments with the 60C or superior cutting capabilities with the 60HH, both models stand ready to elevate your woodworking projects to new heights.
Top Page Image Contents