Ryobi A25RT01 Assembling the Router Table, Attaching the Switch BOX, Attaching the Table Legs

Page 11

ASSEMBLY

ASSEMBLING THE ROUTER TABLE

Assembling the router table involves attaching the switch box, the under table guards, the legs, the router/insert plate assembly, the fence assembly, throat plate, starting pin, and installing the miter gauge to the router table.

ATTACHING THE SWITCH BOX

See Figure 5.

The switch box will come in a bag with the switch box screws and nuts. Use these screws and nuts in the bag to attach the switch box.

Place the router table upside down on a flat surface.

Hold the switch box so that the words ON and OFF on the toggle switch are upside down.

Line up the three holes in the switch box with the three holes on the outside of the front rail, this is the rail that is already installed on the front underside of the router table.

Insert the switch box screws through the holes in the switch box and through the holes in the front rail.

Install the nuts on the back of the switch box screws.

Holding the screws in place with a screwdriver, tighten the nuts onto the screws with a wrench or socket.

ATTACHING THE UNDER TABLE GUARDS

See Figure 6.

The under table guards will come in a bag with the under table guard screws. Use these screws in the bag to attach the under table guards.

Place the router table upside down on a flat surface.

Position the under table guards in front of and behind the insert plate. The front under table guard should have the open ended side facing the back of the router table.

Align the three holes of the under table guards with the holes in the table. The front under table guard will be bolted onto the front rail.

Insert the under table guard screws through the holes and into the table.

Tighten screws with a screwdriver.

ATTACHING THE TABLE LEGS

See Figure 7.

The table legs will come in a bag with the table leg screws. Use the table leg screws in the bag to attach the table legs.

Place router table upside down on a flat, level surface with the front edge closest to you.

Place each leg in a corner of the table. The legs with the warning labels should go in the front, and the legs without the warning labels should go in the back.

NOTE: The table leg with the English language warning should go next to the switch box.

Align the four holes in the legs with the four corresponding threaded holes in the table.

Insert the table leg screws through the holes and into the table.

Tighten screws with a screwdriver.

SWITCH KEY

 

SWITCH BOX

SWITCH

BOX NUT

 

SWITCH BOX

FRONT RAIL

SCREW

Fig. 5

 

 

 

UNDER

UNDER TABLE

TABLE GUARDS

GUARD SCREW

Fig. 6

TABLE LEG

TABLE LEG SCREW

 

FRONT SIDE

RIGHT LEG-

 

 

FRENCH / SPANISH

 

 

LABEL

LEFT LEG-

Fig. 7

 

ENGLISH LABEL

11

Image 11
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction WarrantyRead ALL Instructions General Safety Rules do not USE Awkward Hand Positions Specific Safety Rules Always USE the Articulating Router Cutter BIT Guard Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Connection Speed and WiringElectrical Extension CordsFeatures Throat Plates Reset ButtonSwitch Assembly Starting PINPacking List AssemblyUnpacking Attaching the Table Legs Attaching the Switch BOXAssembling the Router Table Attaching the Under Table GuardsAttaching the Router to the Insert Plate PRE-DRILLING Holes for Through Table Depth AdjustmentInstalling the ROUTER/INSERT Plate Assembly Attaching the Router to the TableKM12VC Making Insert Plate Level Attaching the Fence AssemblyMiter Gauge Installing the Miter GaugeInstall Remove Inserting the Starting PINMounting the Router Table to a Work Bench Attaching the Vacuum HoseClamping the Router Table to a Work Bench Performing a Routing Operation OperationApplications Positioning the Fence Adjusting Depth of CUTAdjusting the Miter Gauge INSERTING/REMOVING CuttersGeneral Maintenance MaintenanceParts and Service