Ryobi RE180PL1 manual See Figures 5, 6, To Adjust Depth of CUT Unplug Your Router

Page 11

ADJUSTMENTS

WARNING:

Do not use cutters with undersized shanks. Under- sized shanks will not tighten properly and could be thrown from the tool causing injury.

WARNING:

Do not use cutters that are larger in diameter than the opening in router base. Use of such cutters will come in contact with the router base and damage both the cutter and router base. This situation could also cause possible loss of control or create other hazardous conditions that could cause possible seri- ous personal injury.

DEPTH OF CUT

See Figures 5, 6 and 7.

When routing a groove that is too deep to safely cut in one pass, it is best to make the cut in several passes. We recommend that cuts be made at a depth not exceeding 1/8 in. (3.2 mm) and that several passes be made to reach deeper cuts.

Proper depth of cut depends on several factors: horsepower of router motor, type of cutter being used, and type of wood being routed. A lightweight, low horsepower router is designed for making shallow cuts. A router with high horsepower rating can safely cut deeper. Small bits, such as veining bits with 1/16 in. (1.6

mm)cutting diameters, are designed to remove only small amounts of wood. Large bits, such as straight-flute bits, are made to remove larger amounts of wood in a single pass. Cuts can be made deeper in soft woods, such as white pine, than in tough hardwoods, like oak or maple. Based upon these considerations, choose a depth of cut that will not place excessive strain on router motor. If you find that extra force is needed or that the motor speed slows down considerably, turn off router and reduce the depth of cut. Then, make the cut in two or more passes.

TO ADJUST DEPTH OF CUT

UNPLUG YOUR ROUTER.

WARNING:

Failure to unplug your router could result in acciden- tal starting causing serious injury.

Raise cutter by unlocking plunge lock lever. See Figure 5.

Adjust hex nuts on threaded post until cutter is inside router subbase.

Place router on a flat surface.

Lower router until tip of cutter barely touches flat surface. See Figure 6.

TO

HEX NUTS

UNLOCK

 

TO

LOCK

PLUNGE

LOCK LEVER

CUTTER INSIDE SUBBASE

Fig. 5

SCALE

ZERO RESET

INDICATOR

WITH RED LINE

LOCK KNOB

STOP BAR

TIP OF CUTTER TOUCHING

WORKPIECE = ZERO DEPTH OF CUT

Fig. 6

CUTTER EXTENDED BELOW SUBBASE

Fig. 7

 

11

Image 11
Contents Save this Manual for Future Reference Operators ManualIntroduction Table of ContentsWork Area General Safety RulesElectrical Safety Personal SafetyAdditional Safety Rules Specific Safety RulesService Symbol Name DESIGNATION/EXPLANATION SymbolsInstructions SpecificationsUnpacking ApplicationsFeatures Change in Depth CUT Front View of RouterAdaptor Power Cord Plunge Lock Lever Collet NUT Router BaseRear View of Router HEX Nuts SubbaseCutter Installation AdjustmentsSee Figures 5, 6 To Adjust Depth of CUT Unplug Your RouterDepth of CUT Optional Depth Control Knob Stop Flange To Install Optional Depth Control KnobOptional Depth Control Knob See FigureOptional Depth Control Knob Plunge Lock Lever To Adjust Depth of CUT Using Optional Depth Control KnobScale Zero Reset Indicator With RED Line Lock Knob Stop BAR Depth StopTo SET Depth Stop Unplug Your Router Speed Selection ChartZero Reset Indicator Variable Speed Control SelectorRouting Motor Housing= OFF Switch OperationRouting Edges Routing by FreehandRouter Work Pilot Guide Pilot BIT EdgingTOP Edge Shaping Router Pilot WorkProper Feeding TOO Fast TOO Slow Rate of FeedFeeding Too Fast Feeding Too SlowDepth GeneralBrush Assemblies LubricationCutters ColletSee Figures 25, 26, To Adjust Plunge Lock Lever Unplug Your RouterThink Safety by Thinking Ahead Router Table AccessoriesOptional Straight Guide Service Model NO. and Serial no