Ryobi RE180PL1 manual Service Model NO. and Serial no

Page 24

OPERATOR'S MANUAL

ELECTRONIC PLUNGE ROUTER

RE180PL1

VARIABLE SPEED – DOUBLE INSULATED

EXTENSION CORD CAUTION

When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the tool will draw. An under- sized cord will cause a drop in line voltage, resulting in over- heating and loss of power. Use the chart to determine the mini- mum wire size required in an extension cord. Only round jack- eted cords should be used.

When working with a tool outdoors, use an extension cord that is designed for outside use. This is indicated by the letters "WA" on the cord's jacket.

Before using any extension cord, inspect it for loose or ex- posed wires and cut or worn insulation.

**Ampere rating

 

 

 

 

 

 

(on tool faceplate)

0-2.0

2.1-3.4

3.5-5.0 5.1-7.0

7.1-12.0

12.1-16.0

 

 

 

 

 

Cord Length

 

Wire Size (A.W.G.)

 

 

 

 

 

 

 

 

 

25'

16

16

16

16

14

14

50'

16

16

16

14

14

12

100'

16

16

14

12

10

CAUTION: Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools or other obstructions while you are working with a power tool.

**Used on 12 gauge - 20 amp circuit.

• SERVICE

Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi Authorized Service Center. You can also check our Web site at www.ryobitools.com for a complete list of Authorized Service Centers.

• MODEL NO. AND SERIAL NO.

The model number of this tool will be found on a plate attached to the motor housing. Please record the model number and serial number in the space provided below.

• HOW TO ORDER REPAIR PARTS

WHEN ORDERING REPAIR PARTS,

ALWAYS GIVE THE FOLLOWING INFORMATION:

• MODEL NUMBER

RE180PL1

SERIAL NUMBER

RYOBI TECHNOLOGIES INC.

1428 Pearman Dairy Road

Anderson, SC 29625

Post Office Box 1207

Anderson, SC 29622

www.ryobitools.com

Phone 1-800-525-2579

983000-448

6-04

Image 24
Contents Operators Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Electrical SafetyPersonal Safety Work AreaSpecific Safety Rules ServiceAdditional Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONSpecifications UnpackingApplications InstructionsFeatures Front View of Router Change in Depth CUTPower Cord Plunge Lock Lever Collet NUT Router Base Rear View of RouterHEX Nuts Subbase AdaptorAdjustments Cutter InstallationTo Adjust Depth of CUT Unplug Your Router Depth of CUTSee Figures 5, 6 To Install Optional Depth Control Knob Optional Depth Control KnobSee Figure Optional Depth Control Knob Stop FlangeTo Adjust Depth of CUT Using Optional Depth Control Knob Scale Zero Reset Indicator With RED Line Lock Knob Stop BARDepth Stop Optional Depth Control Knob Plunge Lock LeverSpeed Selection Chart Zero Reset IndicatorVariable Speed Control Selector To SET Depth Stop Unplug Your RouterMotor Housing = OFF SwitchOperation RoutingRouting by Freehand Routing EdgesPilot BIT Edging TOP Edge ShapingRouter Pilot Work Router Work Pilot GuideProper Feeding Rate of Feed Feeding Too FastFeeding Too Slow TOO Fast TOO SlowGeneral DepthLubrication CuttersCollet Brush AssembliesTo Adjust Plunge Lock Lever Unplug Your Router Think Safety by Thinking AheadSee Figures 25, 26, Accessories Optional Straight GuideRouter Table Service Model NO. and Serial no