Ryobi RE180PL1 manual Routing by Freehand, Routing Edges

Page 16

OPERATION

ROUTING BY FREEHAND

See Figure 16.

When used freehand, your plunge router becomes a flexible and versatile tool. This flexibility makes it possible to easily rout signs, relief sculptures, etc.

There are two basic techniques for freehand routing:

Routing letters, grooves, and patterns into wood.

Routing out the background, leaving the letters or pattern raised above the surface.

When freehand routing, we suggest the following:

Draw or layout the pattern on workpiece.

Choose the appropriate cutter.

NOTE: A core box or V-groove bit is often used for routing letters and engraving objects. Straight bits and ball mills are often used to make relief carvings. Veining bits are used to carve small, intricate details.

Rout the pattern in two or more passes. Make the first pass at 25% of the desired depth of cut. This process will provide better control as well as being a guide for the next pass.

Do not rout deeper than 1/8 in. (3.2 mm) per pass or cut.

Follow these directions when routing by freehand:

Choose the appropriate cutter, set desired depth of cut, carefully check set-up, and secure workpiece.

Make a test cut in a scrap piece of wood from the same workpiece if possible.

Unlock plunge lock lever to raise cutter from any preset depth of cut. This also permits raising cutter inside router subbase.

Place router on workpiece inside pattern to be routed.

Grasp handles securely and press the switch to start your router.

Let motor build to full speed, then gradually plunge cutter into workpiece until stop bar comes into contact with depth stop.

Lock plunge lock lever to secure depth of cut setting.

Begin routing out the pattern, continuing until a complete pass at this depth of cut has been made.

WARNING:

Do not use large router bits for freehand routing. Use of large router bits when freehand routing could cause loss of control or create other hazardous conditions that could cause possible serious personal injury.

Fig. 16

Several cuts that require repositioning of router may be needed for a particular job. If this situation exists, unlock plunge lock lever to raise cutter inside router subbase after each cut, reposition router for next cut, gradually plunge cutter into workpiece until stop bar contacts depth stop, lock plunge lock lever and continue routing.

After all cuts have been made, unlock plunge lock lever, raise cutter inside router subbase, remove router from workpiece, turn off the router, and allow cutter to come to a complete stop.

ROUTING EDGES

Place router on workpiece, making sure the router bit does not contact workpiece. Turn router on and let the motor build to its full speed. Begin your cut, gradually feeding cutter into workpiece.

WARNING:

Keep a firm grip on router with both hands at all times. Failure to do so could result in loss of control leading to possible serious injury.

Upon completion of cut, turn motor off and let it come to a complete stop before removing router from work surface.

WARNING:

Never pull router out of work and place upside down on work surface before the cutter stops.

16

Image 16
Contents Operators Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Electrical SafetyPersonal Safety Work AreaService Specific Safety RulesAdditional Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONSpecifications UnpackingApplications InstructionsFeatures Front View of Router Change in Depth CUTPower Cord Plunge Lock Lever Collet NUT Router Base Rear View of RouterHEX Nuts Subbase AdaptorAdjustments Cutter InstallationDepth of CUT To Adjust Depth of CUT Unplug Your RouterSee Figures 5, 6 To Install Optional Depth Control Knob Optional Depth Control KnobSee Figure Optional Depth Control Knob Stop FlangeTo Adjust Depth of CUT Using Optional Depth Control Knob Scale Zero Reset Indicator With RED Line Lock Knob Stop BARDepth Stop Optional Depth Control Knob Plunge Lock LeverSpeed Selection Chart Zero Reset IndicatorVariable Speed Control Selector To SET Depth Stop Unplug Your RouterMotor Housing = OFF SwitchOperation RoutingRouting by Freehand Routing EdgesPilot BIT Edging TOP Edge ShapingRouter Pilot Work Router Work Pilot GuideProper Feeding Rate of Feed Feeding Too FastFeeding Too Slow TOO Fast TOO SlowGeneral DepthLubrication CuttersCollet Brush AssembliesThink Safety by Thinking Ahead To Adjust Plunge Lock Lever Unplug Your RouterSee Figures 25, 26, Optional Straight Guide AccessoriesRouter Table Service Model NO. and Serial no