Bryant 548D installation instructions II. Lubrication

Page 31

B. Outdoor Coils

Inspect coils monthly. Clean condenser coils annually, and as required by location and outdoor-air conditions.

Clean 2-row coils as follows:

1.Turn off unit power and tag disconnect.

2.Remove top panel screws on outdoor end of unit.

3.Remove outdoor coil corner post. See Fig. 39. To hold top panel open, place coil corner post between top panel and center post. See Fig. 40.

4.Remove device holding coil sections together at return end of outdoor coil. Carefully separate the outer coil section 3 to 4 in. from the inner coil section. See Fig. 41.

5.Use a water hose or other suitable equipment to flush down between the 2 coil sections to remove dirt and debris. Clean the outer surfaces with a stiff brush in the normal manner.

6.Secure the sections together. Reposition the coil sec- tions, and remove the coil corner post from between the top panel and center post. Install the coil corner post and coil center post, and replace all screws.

C.Condensate Drain

Check and clean each year at start of cooling season. In win- ter, keep drain dry or protect against freeze-up.

D. Filters

Clean or replace at start of each heating and cooling season, or more often if operating conditions require it. Replacement filters must be same dimensions as original filters.

E. Outdoor-Air Inlet Screen

Clean screen with steam or hot water and a mild detergent. Do not use disposable filters in place of screens.

F. Belts

Adjust belt tension and pulley alignment at least twice a year or more frequently as operating conditions require.

II. LUBRICATION

A. Compressors

Each compressor is charged with correct amount of oil at the factory.

B. Fan Motor Bearings

Fan motor bearings are permanently lubricated. No further lubrication of outdoor- or indoor-fan motors is required.

Fig. 39 — Cleaning Outdoor Coil

Fig. 40 — Propping Up Top Panel

Fig. 41 — Separating Coil Sections

31

Image 31
Contents Provide Unit Support ContentsSafety Considerations InstallationRoof Curb Details Positioning III. Install Condensate Drain Line and External TrapII. Field Fabricate Ductwork IV. RIG and Place UnitUnit MAX Dimensions Weight Base Unit Dimensions Unit Size 548D Physical Data460-3-60 Field Power SupplyMake Electrical Connections 575-3-60RLA LRA FLA Electrical Data Units Without Electrical Convenience OutletSIZE† TypeMin Electrical Data Units With Electrical Convenience Outlet81/2 Tons FLA VI. Adjust FACTORY-INSTALLED Options 208/230 460 575 Unit VoltageStage Durablade Economizer Installation Durablade Economizer Damper Minimum Position Setting EconoMi$er Component Locations Rear EconoMi$er Flange Installation EconoMi$er Wiring Wiring Diagram for Power Exhaust System VII. Adjust INDOOR-FAN Speed Default Potentiometer SettingsChangeover Set Points Typical Belt-Drive Motor Mounting for Size Continuous BHP Fan Rpm at Motor Pulley SettingsIndoor-Fan Motor Performance Unit INDOOR-FAN Maximum AcceptableStandard Motor Belt Drive Fan Performance 548D090 Vertical Discharge UnitsFan Performance 548D102 Vertical Discharge Units 548D120 10 Tons Standard and Alternate Motors Belt Drive Fan Performance 548D120 Vertical Discharge UnitsFan Performance 548D090 Horizontal Discharge Units Fan Performance 548D102 Horizontal Discharge Units Standard and Alternate Motors Belt Drive Fan Performance 548D120 Horizontal Discharge UnitsSTART-UP Unit Preparation Internal WiringVI. Refrigerant Service Ports PRE-START-UPXI. Heating IX. Adjust GAS InputXII. Safety Relief CoolingIndoor Coil Service CleaningCooling, Units With EconoMi$er DefrostII. Lubrication Refrigerant Charge IV. Economizer AdjustmentCooling Charging Chart 548D102 Heating and Cooling Troubleshooting TroubleshootingProblem Cause Remedy OAT Durablade Economizer TroubleshootingIFC IFODamper position Damper does not openEconoMi$er operation limited To minimum positionTypical Wiring Diagram Must Voltage Page III. START-UP Electrical START-UP ChecklistTemperatures Preliminary Information

548D specifications

The Bryant 548D heat pump stands out in the HVAC market for its robust performance, energy efficiency, and advanced technology. Known for its reliability, this particular model is designed to provide optimal heating and cooling for both residential and light commercial applications.

One of the standout features of the Bryant 548D is its variable-speed compressor, which allows for precise temperature control and enhances comfort levels in any environment. This technology enables the 548D to operate efficiently at different speeds, adjusting its output based on the heating or cooling demand. As a result, homeowners can enjoy consistent temperature regulation without the wide fluctuations typical of single-stage systems.

In addition to the variable-speed compressor, the Bryant 548D utilizes advanced refrigerant technology. It employs the environmentally friendly Puron refrigerant, which not only improves the unit's efficiency but also reduces its carbon footprint. This makes the 548D a sustainable choice for those looking to minimize their environmental impact while still enjoying superior heating and cooling performance.

Another key characteristic of the Bryant 548D is its impressive energy efficiency rating, often exceeding the minimum requirements set by the Department of Energy. With a high Seasonal Energy Efficiency Ratio (SEER) for cooling in warmer months and an excellent Heating Seasonal Performance Factor (HSPF), the 548D minimizes energy consumption while maximizing comfort.

The 548D also features Quiet Operation technology, ensuring that the system runs quietly in the background without disrupting daily activities. This is particularly beneficial for light commercial spaces or homes where noise can be a concern. The sleek design and compact size make the unit easy to install in various settings without occupying excessive space.

Furthermore, Bryant incorporates advanced smart technology within the 548D model. The system can be integrated with smart thermostats, allowing users to monitor and control their heating and cooling settings remotely. This feature not only enhances convenience but also enables homeowners to program their systems for maximum efficiency.

In conclusion, the Bryant 548D heat pump is an exceptional choice for those seeking a reliable, efficient, and technologically advanced heating and cooling solution. Its combination of variable-speed compression, eco-friendly refrigerant, high energy efficiency, and quiet operation positions it well in the competitive HVAC market, making it a top choice for both residential and light commercial applications. By investing in the Bryant 548D, consumers can enjoy superior comfort and lower energy bills year-round.