Multiquip SFG10E manual Assembly INSTRUCTIONS/OPERATIONS

Page 21

ASSEMBLY INSTRUCTIONS/OPERATIONS

FIGURE 26

5)Using a hammer, strike the wider side of the mounting wedge with controlled, direct blows to firmly seat the multi-accessory attachment into the aluminum disc. Usually one or two direct blows will be sufficient to properly retain the attachment.

CAUTION

Do not apply excessive impact force to the mounting wedge to cause splitting. Once the multi-accessory attachment is seated in the aluminum disc, further impact force on the wedge will not increase the seating force.

FIGURE 27

DANGER

DO NOT OPERATETHE SURFACE GRINDERWITHTHE 229019-017 MOUNTING WEDGES IN AN IMPROPER MOUNTING CONFIGURATION. MOUNTING AWEDGE BETWEEN THE MULTI-ACCESSORY ATTACHMENT ANDTHE OUTSIDE RIB OFTHE ALUMINUM DISC CAN ALLOWTHE WEDGETO COME IN DIRECT CONTACT WITH AVERTICALWALL AND/OR FLOOR OBSTRUC- TION. SUCH OCCURRENCE CAN RESULT IN LOSS OF MACHINE CONTROL, PROPERTY DAMAGE AND/ OR PERSONAL INJURY.

BEFORE OPERATINGTHE SURFACE GRINDERWITH ANY MULTI-ACCESSORY ATTACHMENT, DETERMINE THAT NO PORTION OF THE ATTACHMENT AND/OR MOUNTINGWEDGE EXTENDS BEYONDTHE NORMAL PERIMETER OFTHE ALUMINUM DISC.

CAUTION

Improper seating force created by an excessive blow to the mounting wedge will not allow the attachment to properly release from the aluminum disc if direct contact with a foreign object is made. Such occurrence can result in property damage and/or personal injury. The correct seating force for a specific job application is that which is sufficient to retain the attachment, yet still allows it to release from the aluminum disc when direct contact with a foreign object is made.

6)Determine that the multi-accessory attachment is in full contact with the aluminum disc. If not in proper contact, refer to REMOVING A MULTI-ACCESSORY ATTACHMENT (not including multi-segmented, dry diamond blades) FROM THE ROTATING DISC for proper removal procedures.

7)Return the SURFACE GRINDER to its normal operating position.

8)If the machine is to be used immediately, reconnect the extension cord or SURFACE GRINDER to the power source. Determine that the ON/OFF switch located on the operator handle is in the OFF position.

DANGER

UNEXPECTED MACHINE START UP CAN RESULT IN PROPERTY DAMAGE AND/OR PERSONAL INJURY.

SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #2 (05/28/09) — PAGE 21

Image 21
Contents Model SFG10E SILICOSIS/RESPIRATORYWARNINGS Table of Contents WE Accept ALL Major Credit Cards Domestic US Customers dial’ASSISTANCE Appropriee Avant D’UTILISER LE Produit Page Operator Instructional Data Sheet Safety Precautions Safety Precautions Operation MAINTENANCE, Repair and Storage Removing the Surface Grinder from the Pallet AssemblyGrinding Stones Theory of OperationTungsten Carbide Grinding Block Scarifier BlocksStar Flail Pentagonal Flail Beam FlailScarifier Block Bushing SpacerWasherWire brushes Floor BrushesSCRAPE-R-TACH Industrial Floor Coatings Removal System Follow all safety precautions for the safety solvent Multi-Segmented, Dry Diamond Disc Diamond Segment Block Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Starting the SFG10E Surface Grinder on the Jobsite Adjustingthe Operator Handle HeightAssembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Page Stoppingthe SFG10E Surface Grinder Early Age GrindingDefinitions of floor flatness and levelness Defined Versus RandomTraffic Patterns How to Define Surface RegularityTR 34 tolerances for defined traffic floors Preventative Maintenance Check List Observe all applicable safety precautions for the solventChecking V-BELTTENSION and Alignment Installing a Replacement V-BELT or Pulley MAINTENANCE/SERVICEMAINTENANCE/SERVICE Lubrication Requirements Lubrication PointsElectric Motor Service Electric Motor Operational ProblemsAccelerated V-BELTWEAR Uneven Grinding ActionStorage Specifications Page Xxxxx only Not Used on Part NameRemarks Qty Description Suggested Spare PartsOperator Handle Assy Operator Handle AssyMOUNT, Rubber SFWS277 ASSEMBLY, Swivel COVER, SwitchSwitch CAM, SwitchElectric Motor Assy Electric Motor AssyMOUNT, Electric Motor MOTOR, ELECTRIC, 1-1/2 HP, 115 VACPulley Included with ItemWheel Dolly Assy Wheel Dolly AssyWheel ARM, SwingSCRAPER, Wheel WASHER, FLAT, 3/4, PlatedFrame Assy Frame AssyDISC, MULTI-ACCESSORY, LH WeightCONNECTOR, GREASE, 1/4-28 UNF CONNECTOR, GREASE, 1/8 PipeSafety and Dust Shield Assy Safety and Dust Shield AssyBUMPER, Rubber Skirt AssyHOSE, Vacuum STRAP, SkirtScarifier Assy Scarifier AssyBushing HousingSee Note NUT, HEX 3/8 UNC, Nylock PlatedSCRAPE-R-TACH Assy SCRAPE-R-TACH AssySpacer HOLDER, InsertINSERT, Tungsten Carbide NUT, Nylock 5/16-1/8 UNC, PlatedGrinding Block Assy Grinding Block AssyRing BlockWedge Plastic Aggress GrindingDecals DecalsDECAL, Grease Bearings DECAL, WarningDECAL, Motor START/STOP TBD DECAL, MQ Logo Large DECAL, Warning SFSP8E5HP5020Payment Terms Page Mexico United Kingdom United States