Multiquip SFG10E manual Maintenance/Service, Installing a Replacement V-BELT or Pulley

Page 32

FIGURE 41

5)Belt alignment is checked with the straightedge. Place the straightedge squarely against the transmission pulley. Properly aligned pulleys should also place the straightedge squarely against the motor pulley. Remove the straightedge and rotate the motor pulley 120 degrees. FIGURE 42. Recheck alignment with the straightedge. Repeat the process until the motor pulley is rotated a full 360 degrees. Maximum allowable misalignment is + - 1/32 inch. If pulley alignment is not within specifications, refer to INSTALLING A REPLACEMENT V-BELT for specific information.

6)Install the belt guard to the main frame. Determine that all safety related decals affixed to the belt guard are fully readable. If any decal is not fully readable, replace with a factory approved, replacement part only.

7)If the machine is to be used immediately, reconnect the extension cord or SURFACE GRINDER to the power source. Determine that the ON/OFF switch located on the operator handle is in the OFF position

DANGER

UNEXPECTED MACHINE START UP CAN RESULT IN PROPERTY DAMAGE AND/OR PERSONAL INJURY.

FIGURE 42

MAINTENANCE/SERVICE

INSTALLING A REPLACEMENT V-BELT OR PULLEY

Tools Required:

2 1/2 wrenches.

1 16 inch minimum length straightedge.

110 lbs minimum capacity, tension scale or belt tension tool.

1belt tension tool.

Parts Required:

1 V-Belt, P/N SFB45

1 Pulley Assy. P/N SFSG120400

1)Position the SURFACE GRINDER on a suitable work surface with the V-belt approximately at waist level.

2)Remove the belt guard from the main frame. Clean the inside of the belt guard with an appropriate solvent. Check for signs of wear and damage. Secure in a proper storage area.

CAUTION

Observe all applicable safety precautions for the solvent.

3)Using the 1/2-inch wrenches, loosen the motor mounting plate cap screws.

4)With the same wrenches, rotate the motor take-up cap screws counterclockwise to loosen the V-belts and allow the electric motor to slide toward the front of the main frame. FIGURE 43.

FIGURE 43

SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #2 (05/28/09) — PAGE 32

Image 32
Contents Model SFG10E SILICOSIS/RESPIRATORYWARNINGS Table of Contents Domestic US Customers dial WE Accept ALL Major Credit Cards’ASSISTANCE Appropriee Avant D’UTILISER LE Produit Page Operator Instructional Data Sheet Safety Precautions Safety Precautions Operation MAINTENANCE, Repair and Storage Assembly Removing the Surface Grinder from the PalletTheory of Operation Grinding StonesStar Flail Tungsten Carbide Grinding BlockScarifier Blocks Beam Flail Pentagonal FlailSpacerWasher Scarifier Block BushingSCRAPE-R-TACH Industrial Floor Coatings Removal System Wire brushesFloor Brushes Follow all safety precautions for the safety solvent Multi-Segmented, Dry Diamond Disc Diamond Segment Block Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Adjustingthe Operator Handle Height Starting the SFG10E Surface Grinder on the JobsiteAssembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Page Definitions of floor flatness and levelness Stoppingthe SFG10E Surface GrinderEarly Age Grinding How to Define Surface Regularity Defined Versus RandomTraffic PatternsTR 34 tolerances for defined traffic floors Checking V-BELTTENSION and Alignment Preventative Maintenance Check ListObserve all applicable safety precautions for the solvent MAINTENANCE/SERVICE Installing a Replacement V-BELT or PulleyMAINTENANCE/SERVICE Lubrication Points Lubrication RequirementsElectric Motor Service Operational Problems Electric MotorAccelerated V-BELTWEAR Uneven Grinding ActionStorage Specifications Page Remarks Xxxxx only Not Used onPart Name Suggested Spare Parts Qty DescriptionOperator Handle Assy Operator Handle AssyCOVER, Switch MOUNT, Rubber SFWS277 ASSEMBLY, SwivelSwitch CAM, SwitchElectric Motor Assy Electric Motor AssyMOTOR, ELECTRIC, 1-1/2 HP, 115 VAC MOUNT, Electric MotorPulley Included with ItemWheel Dolly Assy Wheel Dolly AssyARM, Swing WheelSCRAPER, Wheel WASHER, FLAT, 3/4, PlatedFrame Assy Frame AssyWeight DISC, MULTI-ACCESSORY, LHCONNECTOR, GREASE, 1/4-28 UNF CONNECTOR, GREASE, 1/8 PipeSafety and Dust Shield Assy Safety and Dust Shield AssySkirt Assy BUMPER, RubberHOSE, Vacuum STRAP, SkirtScarifier Assy Scarifier AssyHousing BushingSee Note NUT, HEX 3/8 UNC, Nylock PlatedSCRAPE-R-TACH Assy SCRAPE-R-TACH AssyHOLDER, Insert SpacerINSERT, Tungsten Carbide NUT, Nylock 5/16-1/8 UNC, PlatedGrinding Block Assy Grinding Block AssyBlock RingWedge Plastic Aggress GrindingDecals DecalsDECAL, Warning DECAL, Grease BearingsDECAL, Motor START/STOP TBD DECAL, MQ Logo Large DECAL, Warning SFSP8E5HP5020Payment Terms Page United States Mexico United Kingdom