Multiquip SFG10E manual Adjustingthe Operator Handle Height

Page 23

DANGER

EXERCISE EXTREME CAUTION WHEN UTILIZING A MECHANICAL DEVICE FOR LIFTINGTHE SURFACE GRINDER. UTILIZE THE MECHANICAL DEVICE IN ACCORDANCE TO BOTH ITS STATED STATIC AND DYNAMIC LOADING ENVELOPES. DO NOT UTILIZE THE MECHANICAL DEVICE UNTIL THIS INFORMA- TION IS PROPERLY KNOWN AND UNDERSTOOD BY ALL APPLICABLE PERSONNEL. FAILURETO PROP- ERLY UTILIZE THE MECHANICAL DEVICE CAN RESULT IN PROPERTY DAMAGE AND/OR PER- SONAL INJURY.

2)To minimize the possibility of damage to the SURFACE GRINDER, always transport in its normal, upright position. All equipment must be secured in/on vehicles with suitable strapping or tie-downs. Personnel should not be transported in the same compartment as equipment and fuel supplies. Consult applicable OSHA, AGA, CGA, etc. regulations for the proper transportation flammable gases.

ASSEMBLY INSTRUCTIONS/OPERATIONS

ADJUSTINGTHE OPERATOR HANDLE HEIGHT

The SFG10E SURFACE GRINDER incorporates a handle that can be adjusted to compensate for variances in operator heights. Correct handle height can increase overall machine productivity and reduce operator fatigue.

1)Loosen both knobs on the lower handle. FIGURE 30.

2)Pull the top handle until the desired height is reached.

3)Tighten both knobs on the lower handle.

FIGURE 29

FIGURE 30

STARTING THE SFG10E SURFACE GRINDER ON THE JOBSITE

1)Position the SURFACE GRINDER on a flat and level surface of firm foundation.

2)Determine that the ON/OFF switch located on the operator handle is in the OFF position.

DANGER

UNEXPECTED MACHINE START UP CAN RESULT IN PROPERTY DAMAGE AND/OR PERSONAL INJURY.

3)The motor is designed to operate from a clean, 20 ampere, 115 VAC, 60 Hz nominal power source. A clean power source refers to the amperage available on the individual electrical circuit selected. Additional electrical products already utilizing the same circuit will reduce the available amperage, resulting in starting and operational difficulties.

SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #2 (05/28/09) — PAGE 23

Image 23
Contents Model SFG10E SILICOSIS/RESPIRATORYWARNINGS Table of Contents WE Accept ALL Major Credit Cards Domestic US Customers dial’ASSISTANCE Appropriee Avant D’UTILISER LE Produit Page Operator Instructional Data Sheet Safety Precautions Safety Precautions Operation MAINTENANCE, Repair and Storage Removing the Surface Grinder from the Pallet AssemblyGrinding Stones Theory of OperationStar Flail Tungsten Carbide Grinding BlockScarifier Blocks Pentagonal Flail Beam FlailScarifier Block Bushing SpacerWasherSCRAPE-R-TACH Industrial Floor Coatings Removal System Wire brushesFloor Brushes Follow all safety precautions for the safety solvent Multi-Segmented, Dry Diamond Disc Diamond Segment Block Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Starting the SFG10E Surface Grinder on the Jobsite Adjustingthe Operator Handle HeightAssembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Page Definitions of floor flatness and levelness Stoppingthe SFG10E Surface GrinderEarly Age Grinding Defined Versus RandomTraffic Patterns How to Define Surface RegularityTR 34 tolerances for defined traffic floors Checking V-BELTTENSION and Alignment Preventative Maintenance Check ListObserve all applicable safety precautions for the solvent Installing a Replacement V-BELT or Pulley MAINTENANCE/SERVICEMAINTENANCE/SERVICE Lubrication Requirements Lubrication PointsElectric Motor Service Uneven Grinding Action Operational ProblemsElectric Motor Accelerated V-BELTWEARStorage Specifications Page Remarks Xxxxx only Not Used onPart Name Qty Description Suggested Spare PartsOperator Handle Assy Operator Handle AssyCAM, Switch COVER, SwitchMOUNT, Rubber SFWS277 ASSEMBLY, Swivel SwitchElectric Motor Assy Electric Motor AssyIncluded with Item MOTOR, ELECTRIC, 1-1/2 HP, 115 VACMOUNT, Electric Motor PulleyWheel Dolly Assy Wheel Dolly AssyWASHER, FLAT, 3/4, Plated ARM, SwingWheel SCRAPER, WheelFrame Assy Frame AssyCONNECTOR, GREASE, 1/8 Pipe WeightDISC, MULTI-ACCESSORY, LH CONNECTOR, GREASE, 1/4-28 UNFSafety and Dust Shield Assy Safety and Dust Shield AssySTRAP, Skirt Skirt AssyBUMPER, Rubber HOSE, VacuumScarifier Assy Scarifier AssyNUT, HEX 3/8 UNC, Nylock Plated HousingBushing See NoteSCRAPE-R-TACH Assy SCRAPE-R-TACH AssyNUT, Nylock 5/16-1/8 UNC, Plated HOLDER, InsertSpacer INSERT, Tungsten CarbideGrinding Block Assy Grinding Block AssyAggress Grinding BlockRing Wedge PlasticDecals DecalsDECAL, Warning SFSP8E5HP5020 DECAL, WarningDECAL, Grease Bearings DECAL, Motor START/STOP TBD DECAL, MQ Logo LargePayment Terms Page Mexico United Kingdom United States