Craftsman 149.236321 owner manual Table of Contents

7.KEEPCHILDRENAWAY

Atlvisitorsshouldbekeptasafedistancefromworkarea.

8.MAKEWORKSHOPKIDPROOF

withpadlocks,masterswitches,orbyremovingstarterkeys.

9.DON'TFORCETOOL

It willdothejobbetterandbesaferattherateforwhichit wasdesigned.

10USERIGHTTOOL.

Don'tforcetoolorattachmenttodoajobforwhichitwasnot

designed.

11WEARPROPERAPPAREL.

Nolooseclothing,gloves,neckties,rings,bracelets,or

jewelrytogetcaughtinmovingpartsNonslipfootwearis.

recommendedWearprotectivehaircoveringtocontainlong.

hair.

12ALWAYSUSESAFETYGLASSES.

Alsousefaceordustmaskif cuttingoperationisdusty EverydayeyeglassesonlyhaveimpactresistantlensesThey. areNOTsafetyglasses.

13SECUREWORK.

UseclampsoravisetoholdworkwhenpracticalIt'ssafer. thanusingyourhandandfreesbothhandstooperate tool.

!4. DON'T OVERREACH

Keep your proper footing and balance at all times.

!5. MAINTAIN TOOLS IN TOP CONDITION

Keep tools sharp and clean for best and safest performance.

Follow instructions for lubricating and changing accessories.

16.DISCONNECT TOOLS FROM POWER SOURCE

before servicing and when changing accessories such as blades, bits, cutters, or when mounting and re-mounting motor.

17.AVOID ACCIDENTAL STARTING

Make sure switch is in "OFF" position before plugging in cord.

18.USE RECOMMENDED ACCESSORIES

Consult the owner's manual for recommended accessories. Use of improper accessories may be hazardous.

19.NEVER STAND ON TOOL

Serious injury could occur if lhe tool is tipped or if the cutting

too] is unintentionally contacted.

20.CHECK DAMAGED PARTS

Before further use of the tool, a guard or other part that is damaged should be carefully checked to ensure that it wilt

operate property and perform its intended function - check

for alignment of moving parts, binding of moving parts,

breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

21.DIRECTION OF FEED

Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.

22.NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don't leave tool until it comes to a complete stop.

23.WEAR EAR PROTECTION

When operating for prolonged period of time,-use of ear pro- tection is recommended.

The operation of any power toot can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety goggles complying with ANSI Z87.1

(shown on Package) before commencing power tool operation. Safety Goggles are available at Sears retail or catalog stores.

TABLE OF CONTENTS

GENERAL		SAFETY		RULES FOR		POWER TOOLS	2, 3
UNPACKING		AND		CHECKING		CONTENT'_	4
SAFETY RULES FOR JOINTER-PLANER							5
ASSEMBLY		............................................					5-7
Depth	of	Cut	Hand		Knob		5
Chip Deflector			.........................................				5
Cutter	Guard		Assembly			..................	5
Fence	................................................						6
Fence	Extension			.....................................			6, 7
Checking		Cutter		Blades			7
INSTALLING		THE		JOINTER-PLANER			8
CONTROLS		AND		ADJUSTMENTS		........................	8, 9
Depth	of	Cut	Hand		Knob		8
Check	Depth		of	Cut	....................................		9
Fence	Adjustment						9
Cutter	Guard		..........................................				9
Guard	Stop						9
ONIOFF		Switch		........................................			9

BASIC	JOINTEH-PLANER						OPERATION	10-12
Setting			the Guard		Stop				10
Feeding			the	Workpiece				10,	11
Using		Holddown/Push				Blocks			11
Beveling,			Chamfering			...............................		11,	12
Using		a Wet/Dry			Vac	...................................			12
MAINTENANCE				.....................................				12,	13
Timing			Belt	Replacement			..............................		12
Cutter		Guard		Return		Spring			12
Blade		Replacement				and	Adjustment		13
General			Maintenance			..................................			13
REPAIR		PARTS		......................................				14, 15
TROUBLE			SHOOTING			...................................			16
How	to		Order	Replacement Parts., ,_					16