Craftsman 149.236321 owner manual Fence Extension, Countersunk Screws

FENCE

1.From among the loose parts "find the following:

(1)Fence

(2)Fence Brackets

(2)Fence Segments

(2)Tilt Indicators

(2)Lock Knobs

(4)114-20 x 3/4" Hex Cap Screws

(4)1/4 Lock Washers

(4)9132 ID x 9/16 OD x 1t16 Thick Washers

(2)9t32 ID x 17/32 OD x 1t8 Thick Washers

(6)#8-32 x 1t2 Flat Head Machine Screws

(6)#8 Flat Washers

(6)#8-32 Hex Nuts

(2)#10-24 x 1/2 Pan Head Machine Screws

(2)#10 Flat Washers

1.Attach fence brackets to base using 114-20 x 3/4 hex cap screws, 9t32 ID x 1/16 thick washers and 1/4 lock washers, snug but do not tighten.

2.Attach fence segments to fence with #8+32 flat head screws, #8 flat washers and #8-32 hex nuts.

3.Place assembled fence on machine with fence brackets inside the fence segments.

4.Position lock knobs with 9t32 ID x 17t32 OD x I/8 thick washers thru slots in fence segments and thread into fence brackets.

5.Place square against face of fence and table surface. Bring fence square to table and tighten lock knobs.

6.THERE MUST BE 1/32" TO 1116" gap between the lower edge of the fence and jeinter tables (with table set for 0" cut). To adjust, move fence assembly by loosening the 1/4-20 x 314 hex cap screws attach* ing the fence brackets to the base. Retighten hex cap screws after adjustment has been made.

7.Recheck squareness of fence.

8.Install tilt indicators with #10-24 x 1/2 pan head machine screw and

#10 flat washers. Set 0 ° of indicators to 0 ° of segments and tighten the screw.

9, The fence should now be adjusted and will accurately measure angles

to 45 ° Inboard and 45 ° outboard (see adjustments section).

LOCK

KNOB

NOTE;

USE

OF WASHERS

\ %

LESS

THAN

118

THICK

MAY

RESULT

IN

FENCE

+

g/32

ID

X

17/320D

TIGHTENING

PROBLEMS

X

1/8

THK

WASHER --_..

FENCE

SEGMENT

FENCE

NUT

_8 FLAT

WASHER

4*8-32

X 112 FLAT

_

_

_"

,+

HEAD MACHINE

SCREW

FENCE.BRACKET

1"/4-20

X314 HEX

_,._.

TILT

INDICATOR

CAP

SCREW

//

LOCK

WASHER

9t32

I0

X 91 IS

GO

X

1116

THK

FLAT

WASHER

4'

10

FLAT

*'10-24

X 112

PAN HEAD

MACHINE

SCREW

TILT INDICATOR SHOULD BE LINED UP WITH

._"THE FENCE SEGMENT AT THE 0+MARK+

FENCE EXTENSION

To aid in edge jointing of workpieees 4" and wider, you may extend the fence height, The extension can be constructed of 1" (3t4" thick) stock pine or hardwood.

Use #8 flat head wood screws of sufficient length to securely attach the extension to the fence. Make sure that the head of the screws are below

the surface of the fence so as not to interfere with the workpiece.

114 '-_ +

For extra stability, additional countersunk holes have been provided near the ends of the fence,

+8

COUNTERSUNK SCREWS