Kenmore 153.33616 owner manual Removing the Old Water Heater

Page 8

Removing the Old Water Heater

q

FIGURE2.

QTurn "OFF" the gas supply to the water heater.

If the main gas line Shut-off valve

serving all gas appliances is used, also shut "OFF" the gas at

each appliance. Leave all gas appliances shut "OFF" until the

water heater installation is

completed, see Figures 2 and 3.

FIGURE&

(_) Turn "OFF" the water supply to the water heater at the water shut off

valve or water meter. Some

installations require that the water be turned off to the entire house,

see Figures 2 and 4.

FIGURE&

(_) Check again to make sure the gas supply is "OFF" to the water heater. Then disconnect the gas supply connection from the gas control valve.

• Burn hazard

-Hot water discharge.

,Keep hands clear of drain valve discharge.

(_ Attach a hose to the water heater drain valve and put the other end in a floor drain or outdoors. Open the water heater drain valve. Open a nearby hot water faucet which will relieve pressure in the water heater and speed draining. The water passing out of the drain valve may be extremely hot. To avoid being scalded, make sure all

connections

are tight and that the

 

water flow is directed away from

FIGURE5.

any person,

see Figures 2 and 5.

 

(_) Disconnect the vent pipe from the draft hood where it connects to the water heater. In most installations the vent pipe can be lifted off after any screw or other attached devices are removed. Dispose of the draft hood. The new water heater has a draft hood which must be used for proper operation,

Qlf you have copper piping to the water heater, the two copper water pipes can be cut with a hacksaw approximately four inches away from where they connect to the water heater, see Figure 6. This will avoid cutting off pipes too short. Additional cuts can be made later if necessary. Disconnect the temperature-pressure relief valve drain line. When the

water heater is drained, disconnect the hose from the drain valve. Close the drain valve. The water heater is now

completely disconnected and ready to be removed.

FIGURE&

If you have galvanized pipes to the water heater, loosen the two galvanized pipes with a pipe wrench at the union in each line. Also disconnect the piping remaining to the water heater, see Figure 7. These pieces should be saved since they may

be needed when reconnecting the new water heater. Disconnect the temperature-pressure relief valve drain line. When the water heater is drained, disconnect the hose from the drain valve. Close the drain valve. The water heater is now completely disconnected and ready to be removed.

Mineral buildup or sediment may have accumulated in the old water heater. This causes the water heater to be much

heavier than normal and this residue, if spilled out, could cause staining.

FIGURE7.

Image 8
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A Model no153.336860 Gallon Propane 153.336900 153.336960 Gallon PropaneSymbol indicates a potentially hazardous Indicates An imminentlyCould result in death or injury Death or injuryImproper installation and use may result Property damage Fire HazardExplosion Hazard Feel water before bathing or showeringPage Recovery DimensionsTank Type Rate GAL8 Ventpipe Diameter ModelWhen Sweat Soldering Materials NeededBasic Tools Additional Tools Needed You may or may not need all these tools, depending on yourThermostat Supplied by CustomersPilot & Main Burner TGORemoving the Old Water Heater Facts to Consider About Location Property Damage HazardOfdoor Insulation BlanketsFront View ALL AIR from Inside Buildings FIGUREllWater Piping Hotter Water can ScaldTemperature-Pressure Relief Valve Installationcompleted UsingInstallation KIT LookatthetopofthewaterheaterThecoldwaterinlet.isFilling the Water Heater Watertemperatureover125FFee/waterbeforebathingor showering Beangledslightlyinward Position,drillasmallholethroughboththeventpipeandSeeFigure17 Gas PipingAgaslineofsufficientsizemustberuntothewaterheater Sediment TrapsGAS Piping with Flexibleconnector What to do if YOU Smell GAS GAS ControlTemperature Regulation Tank Sediment Cleaning Burner Inspection Burner CleaningTemperature-Pressure Relief Valve Operation HousekeepingAnode Rod Inspection DrainingCLOSEthecoldwaterinletvalvetothewaterheater Drain Valve Washer ReplacementService BY-PASS ChartStart Up Conditions Makenecessaryairsupplychangestocorrect Operational ConditionsOperational Conditions Leakage Checkpoints Leaking T&P Valve Page Page Burnerassembly When ORDERINGREPAIRPARTS,ALWAYSGIVETHE Following INFORNT1ONKey No. Part Description Model NumbersModel Numbers Part Description 153.336400HA 153.336464 90034749063457#37 By calling 1-800-366-PART 1-800-366-7278. If the parts youThis ISA Repair Parts LIST, Nota Packing List Limited Warranty on Tanks That Leak Limited Warranty on PartsSears Installation Service Master Protection Agreements