Bryant 213R warranty Physical Data, Unit Size --- Series

PHYSICAL DATA

UNIT SIZE --- SERIES	018---A	024---A	030---A	036---A	042---A	048---A	060---A
Operating Weight (lb)	159	160	208	211	233	269	295
Shipping Weight (lb)	184	185	240	242	262	300	327
Compressor Type				Scroll
REFRIGERANT			Freon→ (R--- 22)
Control			TXV (R--- 22 Hard Shutoff)
Charge (lb)	5.5	6	7.5	8	10	14	15.5
COND FAN			Propeller Type, Direct Drive
Air Discharge				Vertical
Air Qty. (CFM)	2233	2614	2614	3334	3334	4046	4046
Motor HP	1/12	1/10	1/10	1/8	1/8	1/5	1/5
Motor RPM	800	1100	1100	800	800	800	800
COND COIL
Face Area (Sq. ft.)	15.09	15.09	25.87	22.63	17.6	22.63	25.15
Fins per In.	20	20	20	20	20	20	20
Rows	1	1	1	1	2	2	2
Circuits	5	6	6	6	7	8	9
VALVE CONNECT. (In. ID)
Vapor	5/8”	5/8”	3/4”	3/4”	7/8”	7/8”	7/8”
Liquid				3/8”
REFRIGERANT TUBES* (In. OD)
Vapor (0--- 80 Ft. Tube Length)	5/8”	5/8”	3/4”	3/4”	7/8”	7/8”	1--- 1/8”
Liquid (0--- 80 Ft. Tube Length)				3/8”

*For tubing sets between 80 and 200 ft. horizontal or 20 ft. vertical differential, consult the Longline Guideline. Note: See unit Installation Instruction for proper installation.

VAPOR LINE SIZING AND COOLING CAPACITY LOSS 1-STAGE HEAT PUMP APPLICATIONS

LONG LINE APPLICATION: An application is considered					is above indoor unit, and 60 ft. when the outdoor unit is below
”Long line” when the total equivalent tubing length exceeds 80					the indoor unit. Refer to Accessory Usage Guideline below for
ft. or when there is more than 20 Ft. vertical separation between					required accessories. See Long-Line Application Guideline for
indoor and outdoor units. These applications require additional					required piping and system modifications. Also, refer to the table
accessories and system modifications for reliable system					below for the acceptable vapor tube diameters based on the total
operation. The maximum allowable total equivalent length is 250					length to minimize the cooling capacity loss.
ft. The maximum vertical separation is 200 ft. when outdoor unit
						Cooling Capacity Loss (%)
	Acceptable Vapor					Total Equivalent Line Length (ft.)
Unit Nominal Size (Btuh)	Line Diameter OD	Standard Application						Long Line Application
	(in.)							Requires Accessories
		25	50	80	80+		100	125	150	175	200	225	250
18000	5/8	0	1	1		1	2	3	3	4	5	5	6
R---22 HP	3/4	0	0	0		0	0	1	1	1	1	2	2
24000	5/8	0	1	3		3	3	5	6	7	8	9	10
R---22 HP	3/4	0	0	0		0	1	1	1	2	2	3	3
30000	3/4	0	1	1		1	2	3	3	4	5	5	6
R---22 HP	7/8	0	0	0		0	1	1	1	2	2	2	3
36000	3/4	0	1	2		2	3	4	5	6	7	8	9
R---22 HP	7/8	0	0	1		1	1	2	2	3	3	4	4
42000	7/8	0	1	1		1	2	2	3	4	4	5	5
R---22 HP
48000	7/8	0	1	2		2	2	3	4	5	5	6	7
R---22 HP
60000	7/8	1	2	3		3	4	5	7	8	9	10	11
R---22 HP
	1 1/8	0	0	1	1		1	1	2	2	2	3	3

Standard Length = 80 ft. or less total equivalent length

Applications in this area are long line. Accessories are required as shown recommended on Long Line Application Guidelines

Applications in this area may have height restrictions that limit allowable total equivalent length, when outdoor unit is below indoor unit See Long Line Application Guidelines

213R

3