Grizzly G1021x owner manual Inventory, Clean Up, Box 1 Figure Qty, Tools and Hardware

Page 14

Inventory

After all the parts have been removed from the two boxes, you should have the following items:

Box 1: (Figure 3)

Qty

A. Planer Unit (not shown)

1

B.

Extension Tables

2

C.

Dust Port

1

D.

Handwheel

1

Tools and Hardware:

 

Cap Screws M6-1 x 12 (Dust Port)

3

Hex Bolts M6-1 x 12 (Dust Port)

3

Hex Nuts M6-1 (Dust Port)

3

Lock Washers 6mm (Dust Port)

3

Flat Washers 6mm (Dust Port)

3

Hex Bolts M8-1.25 x 25 (Ext. Tables)

6

Set Screws M8-1.25 x 20 (Ext. Tables)

6

Hex Nut M10-1.25 (Handwheel)

1

Flat Washer 10mm (Handwheel)

1

Scale (Hi-Lo) (Handwheel)

1

Key 4 x 4 x 10 (Handwheel)

1

Handwheel Handle (Handwheel)

1

Torx T-Handle Wrench 1⁄2"

1

Flat Head Torx Screws M6-1 x 15

10

Torx Bits T-20

5

Indexable Carbide Inserts

5

Hex Wrenches 3, 4, 5, 6mm

1 ea.

Wrenches 8/10, 12/14mm

1 ea.

In the event that any nonproprietary parts are missing, we would be glad to replace them, or for the sake of expediency, replacements can be obtained at your local hardware store.

B

C

D

Figure 3. G1021X Component Inventory.

-12-

NOTICE

Some hardware/fasteners on the inventory list may arrive pre-installed on the machine. Check these locations before assuming that any items from the inventory list are miss- ing.

Clean Up

The unpainted surfaces are coated with a waxy oil to protect them from corrosion during ship- ment. Remove this protective coating with a sol- vent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser. To clean thoroughly, some parts may need to be removed. For opti- mum performance from your machine, make sure you clean all moving parts or sliding contact surfaces that are coated. Avoid chlo- rine-based solvents, such as acetone or brake parts cleaner, as they may damage painted sur- faces should they come in contact. Always follow the manufacturer’s instructions when using any type of cleaning product.

Gasoline and petroleum products have low flash points and could cause an explosion or fire if used to clean machinery. DO NOT use gasoline or petroleum products to clean the machinery.

Many of the solvents commonly used to clean machinery can be toxic when inhaled or ingest- ed. Lack of ventilation while using these sol- vents could cause seri- ous personal health risks or fire. Take precautions from this hazard by only using cleaning solvents in a well ventilated area.

G1021X 15" Extreme Series Planer

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model G1021X Extreme Series Planer Page Table of Contents Warranty and Returns Contact Info IntroductionForeword Machine Data Sheet G1021X 15 Extreme Series Planer Identification Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Planers 220V Single-Phase Circuit RequirementsSet Up SET UPSet Up Safety Items Needed forBox 1 Figure Qty Clean UpInventory Tools and HardwareSite Considerations Moving & Placing Base UnitHandwheel To install the handwheelExtension Tables Components and Hardware Needed QtyTo check the gearbox oil level To install the dust hoodDust Port Gearbox Oil Level Tighten V-Belts Recommended AdjustmentsTest Run Basic steps of operating the planer are as follows Operation Safety Basic OperationOperations Operation Tips Feed SpeedBed Rollers Adjustment Height RangeTo adjust the bed rollers Tools Needed QtyAccessories Rotacator Precision Planer ToolGrizzly Dial Calipers H4979 H4977Schedule MaintenanceCleaning BeltsLubrication Tension screw locationsRotating/Changing Carbide Cutters ServiceAbout Service To rotate or change a carbide cutterTable Parallelism To adjust the chain tensionChain Tension Maximum Allowable TolerancesTable Parallelism Inspection Rollers & Chip Breaker Heights Distance Below Cutter Edge at BDCAdjustment locations for the chip Breaker To adjust roller spring tension Spring TensionChip Deflector Positioning Chip Deflector Gap Setting QtyTo adjust the deflector position Scale CalibrationShould you find that the pulleys are out of alignment Anti-Kickback FingersPulley Alignment Troubleshooting Guide Motor & Machine OperationCutting Electrical Components Motor Junction Box G1021X 15 Extreme Series PlanerWiring Diagram Planer Table and Base Breakdown Gearbox Breakdown External Gearbox Breakdown Stand and Motor Breakdown Label Placement Parts List DescriptionBearing 6205-2RS PSS01M SET Screw M6-1 X G1021X 15 Extreme Series Planer Warranty and Returns Page Page
Top Page Image Contents