Grizzly G0633/G0634 owner manual Operations, Operation Safety

Page 24

SECTION 4: OPERATIONS

Operation Safety

 

Basic Jointer

 

 

Controls

 

 

 

 

 

 

 

 

Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine.

Loose hair and cloth-

ing could get caught in

machinery and cause seri-

ous personal injury. Keep

loose clothing and long

hair away from moving machinery.

NOTICE

If you have never used this type of machine or equipment before, WE STRONGLY REC- OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training.

This section covers the basic controls used dur- ing routine jointer operations. To use the machine as a planer, you must perform a changeover (see Jointer-Planer Conversion, Page 24)

START Button: Starts motor only if the EMERGENCY OFF button is in the out position.

OFF Button: Stops motor when pushed in.

EMERGENCY OFF Button: Disables the START button. Enable the START button by twisting the EMERGENCY OFF button until it pops out.

 

START

 

Button

 

OFF

EMERGENCY

Button

 

OFF Button

 

Figure 18. START/STOP button locations.

-22-

G0633/G0634 Jointer/Planer Combo Machine

Page 23 Page 25
Image 24
Page 23 Page 25
Contents JOINTER/PLANER Combination Machine Page Table of Contents Introduction ForewordContact Info G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Identification G0634 identification and controlsG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers Circuit Requirements 220V OperationSET UP Set Up SafetyItems Needed for Setup UnpackingCommon Components Qty Jointer/Planer Assembly Not shown InventoryG0633 only Figure G0634 only FigureHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadMoving & Placing Base Unit Front and right rear lifting hole LocationsSetting Outfeed Table Height To install the cutterhead guardCutterhead Guard To set the outfeed table heightKnife Setting Gauge Dust CollectionTo connect a dust collection hose Test Run To test run the machineRecommended Adjustments Tighten V-BeltsOperation Safety OperationsPage To set up the machine for planer operations Basic Planer ControlsJointer-Planer Conversion To change the machine for jointer opera- tions Planer dust port in down positionStock Inspection and Requirements Correct and incorrect grain alignment To cutterhead jointerSquaring Stock Thickness Planer Specific RulesSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerBasic Planer Operation Basic steps of operating the planer are as followsAccessories Rotacator Precision Planer ToolH1302 H4979 H4977Maintenance CleaningSchedule BeltsLubrication Roller chainsPage Service TroubleshootingMotor & Electrical Table JointerCutting Jointer and Planer 43 orChecking/Adjusting Jointer Table Parallelism Checking Outfeed Table ParallelismTools Needed Qty Correcting Outfeed Table to Cutterhead Parallelism Checking Infeed Table ParallelismTo correct outfeed table parallelism Adjusting Jointer Table Parallelism To adjust the jointer table parallelismInfeed Table to Cutterhead Parallelism on To inspect the knives with the knife setting gauge Inspecting Knives G0633 OnlyTo inspect the knives with a straightedge Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 To rotate or change a carbide insertCalibrating Depth Scale Pulley AlignmentTo calibrate the depth scale To align the pulleysSetting Fence Stops To set the 90˚ fence stopAdjusting Table Lock Levers To adjust the table lock leversTo set the 45 fence stop Adjusting Gibs To adjust the table gibsTable Parallelism Adjustments To adjust the table parallelismPlaner Table Parallelism Table Parallelism InspectionTo adjust feed roller spring tension Spring TensionAnti-Kickback Fingers G0633/G0634 magnetic switch Electrical ComponentsWiring Diagram Stand Assembly Parts Breakdown Stand Parts List DescriptionTable Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Cutterhead & Motor Parts List PFH35MDrive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List Fence/Guard List PR01M EXT Retaining Ring 10MMSafety Labels and Cosmetic Parts 801 800 806 807 803 805 808 809 810Warranty and Returns Page Page

G0633/G0634 specifications

The Grizzly G0633 and G0634 models are two impressive machines in the realm of woodworking and metalworking equipment. Both models have gained a loyal following among woodworkers and metal fabricators for their exceptional performance, reliability, and innovative features.

One of the most prominent characteristics of the Grizzly G0633 is its robust build quality. Constructed from heavy-duty cast iron, this bandsaw promises durability and stability during operation, minimizing vibrations and ensuring clean, precise cuts. The G0634, an evolution of the G0633, offers enhanced features that cater to both hobbyists and professionals in various industries.

Both models boast powerful motors that ensure smooth and efficient operation. The G0633 is equipped with a 1 HP motor, while the G0634 comes with a more robust 1.5 HP option, allowing for deeper cuts and handling denser materials. This increased power translates to faster material removal rates and improved productivity on the shop floor.

The G0633/G0634 features a dual-speed function, allowing users to adjust the blade speed according to the material being processed. This flexibility is crucial for achieving optimal results on different materials, whether it's hardwood, softwood, or non-ferrous metals. Additionally, the blade guides on both models are precision-engineered, ensuring minimal friction and longer blade life.

Another standout feature is the large cutting capacity these machines offer. The G0633 provides a resounding 12 inches of throat depth, while the G0634 expands this to 14 inches. This increased capacity is a significant advantage for users tackling larger projects or working with oversized stock.

For user convenience, both models are designed with easy adjustments in mind. The quick-release blade tensioning system simplifies blade changes, while the height-adjustable table enhances user ergonomics. The tables are also made of high-quality cast iron, providing a stable surface for workpieces.

Incorporating advanced safety features, the G0633 and G0634 prioritize operator protection. Each model is equipped with a blade brake system that halts blade movement almost instantaneously when the safety switch is triggered. This is a critical function for preventing accidents during operation.

Ultimately, the Grizzly G0633 and G0634 stand out in the market for their excellent balance of power, versatility, and safety. With their outstanding cutting capabilities and engineered precision, these bandsaws are excellent choices for any workshop aimed at producing high-quality workpieces. Whether for a professional environment or a dedicated hobby shop, both the G0633 and G0634 continue to meet and exceed the expectations of craftsmen and creators everywhere.
Top Page Image Contents