Grizzly G0633/G0634 owner manual Adjusting Table Lock Levers, To set the 45 fence stop

Page 50

To set the 45° fence stop:

1.Loosen the fence tilt lock, and position the fence against the 45° stop bolt.

2.Loosen the lock nut on the 45˚ fence stop bolt (Figure 71).

45° Stop Bolt

Lock Nut

Figure 71. Adjusting fence 45˚ outward.

3.Adjust the 45˚ stop bolt until the fence is exactly 45° outward while resting on the bolt (check the angle with a sliding bevel set to 135° or with a 45° square.

4.Retighten the lock nut loosened in Step 2.

-48-

Adjusting Table Lock

Levers

The table lock levers can be adjusted if they do not lock.

Tools Needed

Qty

Wrench 14 mm

1

To adjust the table lock levers:

 

1.DISCONNECT THE JOINTER/PLANER FROM THE POWER SOURCE!

2.Remove the cutterhead guard.

3.Raise the table on the side of the lock lever that does not lock.

4.Loosen the lock nut on the special bolt under the table, as shown in Figure 72.

Special

Bolt

Lock Nut

Figure 72. Table lock lever bolt.

5.Adjust the bolt height a few turns, lower the table, and try engaging the lock lever.

6.Repeat Steps 3-5until the lever engages, then secure the lock nut.

G0633/G0634 Jointer/Planer Combo Machine

Page 49 Page 51
Image 50
Page 49 Page 51
Contents JOINTER/PLANER Combination Machine Page Table of Contents Contact Info IntroductionForeword G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Identification G0634 identification and controlsG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers Circuit Requirements 220V OperationItems Needed for Setup SET UPSet Up Safety UnpackingG0633 only Figure Common Components Qty Jointer/Planer Assembly Not shownInventory G0634 only FigureHardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadMoving & Placing Base Unit Front and right rear lifting hole LocationsCutterhead Guard Setting Outfeed Table HeightTo install the cutterhead guard To set the outfeed table heightTo connect a dust collection hose Knife Setting GaugeDust Collection Test Run To test run the machineRecommended Adjustments Tighten V-BeltsOperation Safety OperationsPage Jointer-Planer Conversion To set up the machine for planer operationsBasic Planer Controls To change the machine for jointer opera- tions Planer dust port in down positionStock Inspection and Requirements Correct and incorrect grain alignment To cutterhead jointerSquaring Stock Thickness Planer Specific RulesSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerBasic Planer Operation Basic steps of operating the planer are as followsAccessories Rotacator Precision Planer ToolH1302 H4979 H4977Schedule MaintenanceCleaning BeltsLubrication Roller chainsPage Motor & Electrical ServiceTroubleshooting Table JointerCutting Jointer and Planer 43 orTools Needed Qty Checking/Adjusting Jointer Table ParallelismChecking Outfeed Table Parallelism To correct outfeed table parallelism Correcting Outfeed Table to Cutterhead ParallelismChecking Infeed Table Parallelism Infeed Table to Cutterhead Parallelism on Adjusting Jointer Table ParallelismTo adjust the jointer table parallelism To inspect the knives with a straightedge To inspect the knives with the knife setting gaugeInspecting Knives G0633 Only Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 To rotate or change a carbide insertTo calibrate the depth scale Calibrating Depth ScalePulley Alignment To align the pulleysSetting Fence Stops To set the 90˚ fence stopTo set the 45 fence stop Adjusting Table Lock LeversTo adjust the table lock levers Adjusting Gibs To adjust the table gibsPlaner Table Parallelism Table Parallelism AdjustmentsTo adjust the table parallelism Table Parallelism InspectionTo adjust feed roller spring tension Spring TensionAnti-Kickback Fingers G0633/G0634 magnetic switch Electrical ComponentsWiring Diagram Stand Assembly Parts Breakdown Stand Parts List DescriptionTable Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Cutterhead & Motor Parts List PFH35MDrive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List Fence/Guard List PR01M EXT Retaining Ring 10MMSafety Labels and Cosmetic Parts 801 800 806 807 803 805 808 809 810Warranty and Returns Page Page

G0633/G0634 specifications

The Grizzly G0633 and G0634 models are two impressive machines in the realm of woodworking and metalworking equipment. Both models have gained a loyal following among woodworkers and metal fabricators for their exceptional performance, reliability, and innovative features.

One of the most prominent characteristics of the Grizzly G0633 is its robust build quality. Constructed from heavy-duty cast iron, this bandsaw promises durability and stability during operation, minimizing vibrations and ensuring clean, precise cuts. The G0634, an evolution of the G0633, offers enhanced features that cater to both hobbyists and professionals in various industries.

Both models boast powerful motors that ensure smooth and efficient operation. The G0633 is equipped with a 1 HP motor, while the G0634 comes with a more robust 1.5 HP option, allowing for deeper cuts and handling denser materials. This increased power translates to faster material removal rates and improved productivity on the shop floor.

The G0633/G0634 features a dual-speed function, allowing users to adjust the blade speed according to the material being processed. This flexibility is crucial for achieving optimal results on different materials, whether it's hardwood, softwood, or non-ferrous metals. Additionally, the blade guides on both models are precision-engineered, ensuring minimal friction and longer blade life.

Another standout feature is the large cutting capacity these machines offer. The G0633 provides a resounding 12 inches of throat depth, while the G0634 expands this to 14 inches. This increased capacity is a significant advantage for users tackling larger projects or working with oversized stock.

For user convenience, both models are designed with easy adjustments in mind. The quick-release blade tensioning system simplifies blade changes, while the height-adjustable table enhances user ergonomics. The tables are also made of high-quality cast iron, providing a stable surface for workpieces.

Incorporating advanced safety features, the G0633 and G0634 prioritize operator protection. Each model is equipped with a blade brake system that halts blade movement almost instantaneously when the safety switch is triggered. This is a critical function for preventing accidents during operation.

Ultimately, the Grizzly G0633 and G0634 stand out in the market for their excellent balance of power, versatility, and safety. With their outstanding cutting capabilities and engineered precision, these bandsaws are excellent choices for any workshop aimed at producing high-quality workpieces. Whether for a professional environment or a dedicated hobby shop, both the G0633 and G0634 continue to meet and exceed the expectations of craftsmen and creators everywhere.
Top Page Image Contents