Grizzly G0633/G0634 owner manual To change the machine for jointer opera- tions

Page 27

5.Turn the table lock lever (Figure 24) clock- wise, pull it out, and turn the table up. The table will lock into place when raised to its highest position as shown in Figure 25.

Table Lock

Lever

Figure 24. Infeed table lock lever.

Figure 25. Infeed table in "up" position.

6.Raise the outfeed table in the same manner as you did with the infeed table.

7. Swing the planer dust port clockwise over the cutterhead as shown in Figure 26.

Planer Dust

Port

Figure 26. Planer dust port setup.

G0633/G0634 Jointer/Planer Combo Machine

8.Connect the dust hose to the planer dust port.

9.Flip the change lever (Figure 22) up.

To change the machine for jointer opera- tions:

1. Lower the planer table to below the 4" mark on the table height scale.

2.Reverse Steps 2-9in the previous subsec- tion. Pull up on the table lock knobs to lower the table. Make sure you lower the planer dust port to the "down" position (as shown in Figure 27).

Planer Dust Port

Figure 27. Planer dust port in "down" position.

Serious personal injury could occur if you place your fingers between the tables and base or between pivot points. Your hands could be pinched or crushed!

-25-

Page 26 Page 28
Image 27
Page 26 Page 28
Contents JOINTER/PLANER Combination Machine Page Table of Contents Introduction ForewordContact Info G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0634 identification and controls IdentificationG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers 220V Operation Circuit RequirementsUnpacking SET UPSet Up Safety Items Needed for SetupG0634 only Figure Common Components Qty Jointer/Planer Assembly Not shownInventory G0633 only FigureHardware Recognition Chart Floor Load Clean UpPlacement Location Site ConsiderationsFront and right rear lifting hole Locations Moving & Placing Base UnitTo set the outfeed table height Setting Outfeed Table HeightTo install the cutterhead guard Cutterhead GuardKnife Setting Gauge Dust CollectionTo connect a dust collection hose To test run the machine Test RunTighten V-Belts Recommended AdjustmentsOperations Operation SafetyPage To set up the machine for planer operations Basic Planer ControlsJointer-Planer Conversion Planer dust port in down position To change the machine for jointer opera- tionsCorrect and incorrect grain alignment To cutterhead jointer Stock Inspection and RequirementsThickness Planer Specific Rules Squaring StockTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingBasic steps of operating the planer are as follows Basic Planer OperationRotacator Precision Planer Tool AccessoriesH4979 H4977 H1302Belts MaintenanceCleaning ScheduleRoller chains LubricationPage Table Jointer ServiceTroubleshooting Motor & Electrical43 or Cutting Jointer and PlanerChecking/Adjusting Jointer Table Parallelism Checking Outfeed Table ParallelismTools Needed Qty Correcting Outfeed Table to Cutterhead Parallelism Checking Infeed Table ParallelismTo correct outfeed table parallelism Adjusting Jointer Table Parallelism To adjust the jointer table parallelismInfeed Table to Cutterhead Parallelism on To inspect the knives with the knife setting gauge Inspecting Knives G0633 OnlyTo inspect the knives with a straightedge Adjusting/Replacing Knives G0633 To adjust/replace the knives To rotate or change a carbide insert Replacing Carbide Inserts G0634To align the pulleys Calibrating Depth ScalePulley Alignment To calibrate the depth scaleTo set the 90˚ fence stop Setting Fence StopsAdjusting Table Lock Levers To adjust the table lock leversTo set the 45 fence stop To adjust the table gibs Adjusting GibsTable Parallelism Inspection Table Parallelism AdjustmentsTo adjust the table parallelism Planer Table ParallelismSpring Tension To adjust feed roller spring tensionAnti-Kickback Fingers Electrical Components G0633/G0634 magnetic switchWiring Diagram Stand Assembly Parts Breakdown Description Stand Parts ListTable Assembly Parts Breakdown & List Cutterhead & Motor Breakdown PFH35M Cutterhead & Motor Parts ListDrive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List PR01M EXT Retaining Ring 10MM Fence/Guard List801 800 806 807 803 805 808 809 810 Safety Labels and Cosmetic PartsWarranty and Returns Page Page

G0633/G0634 specifications

The Grizzly G0633 and G0634 models are two impressive machines in the realm of woodworking and metalworking equipment. Both models have gained a loyal following among woodworkers and metal fabricators for their exceptional performance, reliability, and innovative features.

One of the most prominent characteristics of the Grizzly G0633 is its robust build quality. Constructed from heavy-duty cast iron, this bandsaw promises durability and stability during operation, minimizing vibrations and ensuring clean, precise cuts. The G0634, an evolution of the G0633, offers enhanced features that cater to both hobbyists and professionals in various industries.

Both models boast powerful motors that ensure smooth and efficient operation. The G0633 is equipped with a 1 HP motor, while the G0634 comes with a more robust 1.5 HP option, allowing for deeper cuts and handling denser materials. This increased power translates to faster material removal rates and improved productivity on the shop floor.

The G0633/G0634 features a dual-speed function, allowing users to adjust the blade speed according to the material being processed. This flexibility is crucial for achieving optimal results on different materials, whether it's hardwood, softwood, or non-ferrous metals. Additionally, the blade guides on both models are precision-engineered, ensuring minimal friction and longer blade life.

Another standout feature is the large cutting capacity these machines offer. The G0633 provides a resounding 12 inches of throat depth, while the G0634 expands this to 14 inches. This increased capacity is a significant advantage for users tackling larger projects or working with oversized stock.

For user convenience, both models are designed with easy adjustments in mind. The quick-release blade tensioning system simplifies blade changes, while the height-adjustable table enhances user ergonomics. The tables are also made of high-quality cast iron, providing a stable surface for workpieces.

Incorporating advanced safety features, the G0633 and G0634 prioritize operator protection. Each model is equipped with a blade brake system that halts blade movement almost instantaneously when the safety switch is triggered. This is a critical function for preventing accidents during operation.

Ultimately, the Grizzly G0633 and G0634 stand out in the market for their excellent balance of power, versatility, and safety. With their outstanding cutting capabilities and engineered precision, these bandsaws are excellent choices for any workshop aimed at producing high-quality workpieces. Whether for a professional environment or a dedicated hobby shop, both the G0633 and G0634 continue to meet and exceed the expectations of craftsmen and creators everywhere.
Top Page Image Contents