Grizzly G0633/G0634 owner manual Bevel Cutting, To bevel cut on the jointer

Page 32

Bevel Cutting

The purpose of bevel cutting is to cut a specific angle into the edge of a workpiece (see Figures 36 & 37).

The Model G0633/G0634 has preset fence stops at 45˚ outward and 90˚. If your situation requires a different angle, the preset fence stops can be easily adjusted for your needs.

NOTICE

If you are not experienced with a jointer, set the depth of cut to 0", and practice feeding the workpiece across the tables as described below. This procedure will better prepare you for the actual operation.

Figure 36. Typical bevel cutting operation.

Figure 37. Illustration of bevel cutting results.

-30-

To bevel cut on the jointer:

1.Read and understand SECTION 1: SAFETY, beginning on Page 8.

2.Make sure your stock has been inspected for dangerous conditions as described in the Stock Inspection & Requirements instruc- tions, beginning on Page 26.

3.Set the cutting depth for your operation. (We suggest between 1⁄16" and 1⁄8" for bevel cut- ting, using a more shallow depth for hard wood species or for wide stock.)

4.Make sure your fence is set to the angle of your desired cut.

5.If your workpiece is cupped (warped), place it so the concave side is face down on the surface of the infeed table.

6.Start the jointer.

7.With a push block in your leading hand, press the workpiece against the table and fence with firm pressure, and feed the workpiece over the cutterhead.

Note: If your leading hand gets within 4" of the cutterhead, lift it up and over the cutterhead, and place the push block on the portion of the workpiece that is on the outfeed table. Now, focus your pressure on the outfeed end of the workpiece while feed- ing, and repeat the same action with your trailing hand when it gets within 4" of the cutterhead. To keep your hands safe, DO NOT let them get closer than 4" from the cutterhead when it is moving!

8.Repeat Step 7 until the angled cut is satis- factory to your needs.

G0633/G0634 Jointer/Planer Combo Machine

Page 31 Page 33
Image 32
Page 31 Page 33
Contents JOINTER/PLANER Combination Machine Page Table of Contents Contact Info IntroductionForeword G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Identification G0634 identification and controlsG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers Circuit Requirements 220V OperationSET UP Set Up SafetyItems Needed for Setup UnpackingCommon Components Qty Jointer/Planer Assembly Not shown InventoryG0633 only Figure G0634 only FigureHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadMoving & Placing Base Unit Front and right rear lifting hole LocationsSetting Outfeed Table Height To install the cutterhead guardCutterhead Guard To set the outfeed table heightTo connect a dust collection hose Knife Setting GaugeDust Collection Test Run To test run the machineRecommended Adjustments Tighten V-BeltsOperation Safety OperationsPage Jointer-Planer Conversion To set up the machine for planer operationsBasic Planer Controls To change the machine for jointer opera- tions Planer dust port in down positionStock Inspection and Requirements Correct and incorrect grain alignment To cutterhead jointerSquaring Stock Thickness Planer Specific RulesSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerBasic Planer Operation Basic steps of operating the planer are as followsAccessories Rotacator Precision Planer ToolH1302 H4979 H4977Maintenance CleaningSchedule BeltsLubrication Roller chainsPage Service TroubleshootingMotor & Electrical Table JointerCutting Jointer and Planer 43 orTools Needed Qty Checking/Adjusting Jointer Table ParallelismChecking Outfeed Table Parallelism To correct outfeed table parallelism Correcting Outfeed Table to Cutterhead ParallelismChecking Infeed Table Parallelism Infeed Table to Cutterhead Parallelism on Adjusting Jointer Table ParallelismTo adjust the jointer table parallelism To inspect the knives with a straightedge To inspect the knives with the knife setting gaugeInspecting Knives G0633 Only Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 To rotate or change a carbide insertCalibrating Depth Scale Pulley AlignmentTo calibrate the depth scale To align the pulleysSetting Fence Stops To set the 90˚ fence stopTo set the 45 fence stop Adjusting Table Lock LeversTo adjust the table lock levers Adjusting Gibs To adjust the table gibsTable Parallelism Adjustments To adjust the table parallelismPlaner Table Parallelism Table Parallelism InspectionTo adjust feed roller spring tension Spring TensionAnti-Kickback Fingers G0633/G0634 magnetic switch Electrical ComponentsWiring Diagram Stand Assembly Parts Breakdown Stand Parts List DescriptionTable Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Cutterhead & Motor Parts List PFH35MDrive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List Fence/Guard List PR01M EXT Retaining Ring 10MMSafety Labels and Cosmetic Parts 801 800 806 807 803 805 808 809 810Warranty and Returns Page Page

G0633/G0634 specifications

The Grizzly G0633 and G0634 models are two impressive machines in the realm of woodworking and metalworking equipment. Both models have gained a loyal following among woodworkers and metal fabricators for their exceptional performance, reliability, and innovative features.

One of the most prominent characteristics of the Grizzly G0633 is its robust build quality. Constructed from heavy-duty cast iron, this bandsaw promises durability and stability during operation, minimizing vibrations and ensuring clean, precise cuts. The G0634, an evolution of the G0633, offers enhanced features that cater to both hobbyists and professionals in various industries.

Both models boast powerful motors that ensure smooth and efficient operation. The G0633 is equipped with a 1 HP motor, while the G0634 comes with a more robust 1.5 HP option, allowing for deeper cuts and handling denser materials. This increased power translates to faster material removal rates and improved productivity on the shop floor.

The G0633/G0634 features a dual-speed function, allowing users to adjust the blade speed according to the material being processed. This flexibility is crucial for achieving optimal results on different materials, whether it's hardwood, softwood, or non-ferrous metals. Additionally, the blade guides on both models are precision-engineered, ensuring minimal friction and longer blade life.

Another standout feature is the large cutting capacity these machines offer. The G0633 provides a resounding 12 inches of throat depth, while the G0634 expands this to 14 inches. This increased capacity is a significant advantage for users tackling larger projects or working with oversized stock.

For user convenience, both models are designed with easy adjustments in mind. The quick-release blade tensioning system simplifies blade changes, while the height-adjustable table enhances user ergonomics. The tables are also made of high-quality cast iron, providing a stable surface for workpieces.

Incorporating advanced safety features, the G0633 and G0634 prioritize operator protection. Each model is equipped with a blade brake system that halts blade movement almost instantaneously when the safety switch is triggered. This is a critical function for preventing accidents during operation.

Ultimately, the Grizzly G0633 and G0634 stand out in the market for their excellent balance of power, versatility, and safety. With their outstanding cutting capabilities and engineered precision, these bandsaws are excellent choices for any workshop aimed at producing high-quality workpieces. Whether for a professional environment or a dedicated hobby shop, both the G0633 and G0634 continue to meet and exceed the expectations of craftsmen and creators everywhere.
Top Page Image Contents