Special safety advice for polishing

b)To ensure the highest level of opera- tional safety, the disc guard cover must be attached to the electrical power tool and set in such a way that the smallest possible area of the abrasive consumable is exposed to the operator. The disc guard cover is there to protect the operator from pieces breaking oﬀ and accidental contact with the abrasive consumable.

c)Abrasive consumables must be used only for their recommended purpos- es, For example: never grind with the side face of a cutting disc. Cutting discs are intended for removing material using the edge of the disc. Sideways forces on these abrasive consumables can cause them to break.

d)Always use an undamaged mounting flange of the correct size and shape for your selected grinding disc. Suitable ﬂanges support the grinding disc and reduce the chance of it breaking. Flanges for cutting discs are diﬀerent from the ﬂanges for other abrasive discs.

e)Do not use chainsaw blades or serrat- ed saw blades. Such insertion tools often cause the tool to recoil or you to lose control of the power tool.

Further special safety advice for disc-cutting

a)Avoid snagging the cutting disc and do not use too much contact pressure. Do not attempt to make excessively deep cuts. Overloading the cutting disc in- creases the load and the tendency of the disc to twist or snag in the cut, making kickback or disc breakage more likely.

b)Avoid the area in front of or behind the rotating cutting disc. If the cutting disc is moving away from you at the point of con- straint in the workpiece, then, in the event of

a kickback, the electrical power tool and the rotating disc may be thrown towards you.

c)If the cutting disc jams or you stop work for a while, switch the device

off and hold it until the disc comes to a complete stop. Never attempt to pull the still rotating cutting disc out of the cut as this could cause kickback. Determine and rectify the reason for the jamming.

d)Do not switch on the device if the cut- ting disc is in the workpiece. Allow the cutting disc to reach full speed before carefully continuing with the cut. Otherwise the disc could snag, jump out of the workpiece or cause a kickback.

e)Support boards or workpieces whilst cutting to reduce the risk of kickback caused by a jammed cutting disc. Large workpieces may bend under their own weight. The workpiece must be supported to both sides of the cutting disc and particularly near the cutting disc and at the workpiece edge.

f)Be particularly careful when pocket cutting in existing walls or other areas where you cannot see what you are cutting into. The cutting disc plunged into the surface could cut through gas or water pipes, electricity cables or other objects and cause kickback.

Special safety advice for abrading using sandpaper

Do not use over-sized sanding sheets. Follow the manufacturer’s recommen- dations for sanding sheet size. Sanding sheets that project beyond the backing pad could cause injury in addition to jamming, tear- ing of the sheet or kickback.

Do not use the polishing bonnet if it has any loose parts, in particular the fastening cords. Tuck the fastening cords away or trim them. Loose fastening cords rotat- ing with the attachment could catch your ﬁngers or become trapped in the workpiece.

GB/IE

PMGS 12 A1 specifications

The Parkside PMGS 12 A1 is a versatile and efficient cordless angle grinder, specifically designed for both home improvement enthusiasts and professional users. This powerful tool is part of the Parkside range known for delivering quality and affordability, making it an excellent addition to any toolkit.

One of the standout features of the PMGS 12 A1 is its 12V lithium-ion battery system. This battery technology provides consistent performance and longevity, ensuring users can tackle a variety of tasks without interruption. The tool is lightweight, weighing in at just over 1.5 kilograms, which enhances maneuverability and reduces fatigue during extended use.

The angle grinder is equipped with a powerful motor that operates at a no-load speed of up to 19,500 RPM. This high RPM rate allows for efficient cutting, grinding, and polishing on various materials such as metal, stone, and even ceramics. Users will appreciate the tool's easy-to-use design, highlighted by its variable speed control feature that allows for optimal settings depending on the job at hand.

Safety is a key concern in power tools, and the PMGS 12 A1 incorporates several safety features. These include a protective cover that can be easily adjusted without tools, and a well-placed safety switch that prevents accidental activation. The ergonomic design of the tool allows for a comfortable grip, reducing strain during prolonged use.

Another notable aspect of the Parkside PMGS 12 A1 is its compatibility with a range of discs and attachments. Users can easily swap out grinding discs and cut-off wheels to suit their specific projects, enhancing the tool's versatility. This feature is especially beneficial for those who tackle various tasks around the home or on construction sites.

In conclusion, the Parkside PMGS 12 A1 stands out as a reliable, user-friendly cordless angle grinder. Its powerful motor, lightweight design, and safety features cater to both hobbyists and professionals. With its versatility in handling different materials and tasks, this tool represents an excellent balance of performance and practicality, making it a valuable asset for any DIY enthusiast or professional tradesperson.