Stanley Black & Decker MB05 Proper Care of Tool Bits, Tool Failure not Covered Under Warranty

Page 19

PROPER CARE OF TOOL BITS

Tool bits are made and heat treated to specification.

Tool bits, however well made, are wear parts, and are used in the most destructive applications. Even when the hydraulic breaker is used properly, and the operator is an experienced one, a tool bit may become damaged. When a tool bit has been damaged, it is useful to de- termine the cause immediately in order to prevent the damage from occurring again.

All Stanley tool bits are machined and hardened for maximum performance. Care must be taken to maintain the tools original condition for optimum productivity and life expectancy. It is not uncommon for an operator who is unfamiliar with using a hammer to break a point. This is part of the learning experience.

Listed below are several methods to determine tool fail- ure and will quickly aid in warranty determination.

TOOL FAILURE NOT COVERED UNDER WARRANTY

BLANK FIRING OR FREE RUNNING

This occurs when the tool is not in proper contact with the work, thus causing the energy produced by the ham- mer to be concentrated on the tool retainer(s) and the retainer slot(s) on the tool itself. Caution should be used to prevent the hammer from sliding off slanted surfaces or when breaking through thin material.

The illustration below is typical of the kind of breakage that occurs from excessive blank firing.

WORN-OUT FRONT BUSHING(S) OR RETAINER PIN(S)

Worn-out front bushing(s) will cause the tool to become misaligned inside the hammer. This misalignment will cause uneven contact between the piston and tool, thus causing stress to concentrate on one particular area of the tool. This can also cause the tool to bind inside the hammer. Call your dealer for acceptable wear allow- ances.

Worn-out retainer pin(s) will cause uneven loading on the pin(s) themselves, causing failure of the tool or re- tainer pin(s). This will also cause excessive wear to the front bushing(s).

METAL-TO-METAL CONTACT

Extreme caution should be used to avoid scratches or gouges on the surface of the tool. These areas create a stress concentration Metal-to-Metal Contact point, thus weakening the tool.

Another form of metal-to-metal contact is galling, which usually occurs from the lack of lubrication. Special care should be taken to keep the tool shank lubricated every two (2) to three (3) hours.

Steel failures that were caused by surface damage take two main forms. The simplest form is caused by deep scratches on working steel surface. The broken surface has a shell pattern around the starting point of failure, similar to the one in the fatigue failure. The other parts of the broken surface are brittle. These failures work slowly through the steel until it suddenly parts completely.

The second form of failure caused by surface damage occurs when there are deep scratches on working steel surface and there was also excessive bending stress. The broken surface also shows the shell pattern, but the other parts of the broken surface are brittle and usually have a “lip” like that in a stress failure.

MB05 User Manual ◄ 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents MB05 Weisbeck, Andy Declaration of ConformityTable of Contents Local Safety Regulations Safety SymbolsSafety Precautions Be Thoroughly Trained Before Operating the Unit Alone Obey Safety RulesKnow the Work Conditions Safety Precautions Tool Stickers & Tags MB05PRE-OPERATION Procedures PRE-INSTALLATION InstructionsOperation Long Term Storage LOW Temperature WARM-UP ProcedureSecuring the Tool BIT Excavators Operating the BreakerPreparation for USE Positioning the Carrier BackhoesBreaking Maintain Down PressureBreaker tool bit binding Blank FiringGrease the BIT Underwater UsageProblem Cause Solution TroubleshootingDaily Maintenance Checks MaintenanceTool Stop and Lower Bushing Charging the Accumulator When disengaging the tester a POP of nitrogen is normalNEW Reject Limit Wear TolerancesBlank Firing or Free Running Tool Failure not Covered Under WarrantyWORN-OUT Front Bushings or Retainer Pins Proper Care of Tool BitsMushrooming CorrosionPrying Internal Material Flaw Tool Failure Covered Under WarrantyChisel MoilBlunt Test Procedure Flow Test ProceduresHeat Load Test TroubleshootingTool Definition of TermsTorque Table SpecificationsMiscellaneous AccessoriesService Tools Description Tool BitsMB05 Power Cell Illustration QTY Description MB05 Power Cell Parts List70766 MB05E04 MB05 Housing PartsMB05 Skid Steer Mounting Brkt MB05S04 C&P027 TOP Skid Steer 70768 MB05E05 MB05S05 Skid Steer Xchange TOP

MB05 specifications

The Stanley Black & Decker MB05 is a powerful and versatile tool that caters to the needs of professionals and DIY enthusiasts alike. Designed for robust performance, this model exemplifies the company’s commitment to innovation and quality.

One of the main features of the MB05 is its sturdy construction, ensuring durability even in the most demanding work environments. The design incorporates high-quality materials that withstand heavy use, making it ideal for both industrial and residential applications. The ergonomic handle enhances comfort during prolonged use, reducing fatigue and improving user experience.

In terms of technology, the MB05 boasts a powerful motor capable of delivering high torque while maintaining efficiency. This motor enables the tool to handle a variety of tasks, from light-duty jobs to more intensive applications. Additionally, the MB05 is equipped with an advanced battery management system that provides excellent runtime and reduces charging time. The inclusion of lithium-ion battery technology further enhances performance by offering longer-lasting power and less downtime.

The MB05 features a versatile speed control mechanism, allowing users to adjust the tool's velocity according to the task at hand. This adaptability is particularly beneficial for users working on various materials, ensuring precise results every time. Moreover, the built-in LED light illuminates the work area, providing increased visibility in dimly lit spaces.

Another characteristic worth noting is the tool’s compatibility with a wide range of accessories. This versatility allows users to customize their experience and tackle diverse projects, from drilling to fastening. The quick-release chuck mechanism simplifies the process of changing accessories, saving valuable time and effort.

In summary, the Stanley Black & Decker MB05 is a robust and efficient tool designed for both professional and personal use. With its durable construction, powerful motor, advanced battery technology, adjustable speed control, and compatibility with various accessories, it represents a valuable addition to any toolbox. Users can rely on the MB05 to deliver exceptional performance and meet their diverse project needs effectively. With Stanley Black & Decker’s reputation for quality, the MB05 is an investment that promises reliability and satisfaction across various applications.
Top Page Image Contents