Miller Electric ICE-80CX, 3080 manual California Proposition 65 Warnings

Page 7

1-3. Additional Symbols For Installation, Operation, And Maintenance

HOT PARTS can cause severe burns.

DDo not touch hot parts bare handed.

DAllow cooling period before working on torch.

MOVING PARTS can cause injury.

DKeep away from moving parts such as fans.

DKeep all doors, panels, covers, and guards closed and securely in place.

FLYING METAL can injure eyes.

DWear safety glasses with side shields or face shield.

MAGNETIC FIELDS can affect pacemakers.

DPacemaker wearers keep away.

DWearers should consult their doctor before go- ing near plasma arc cutting operations.

OVERUSE can cause OVERHEATING.

DAllow cooling period; follow rated duty cycle.

DReduce amperage (thickness) or reduce duty cycle before starting to cut again.

FIRE OR EXPLOSION hazard.

D Do not locate unit on, over, or near combustible surfaces.

DDo not install unit near flammables.

DDo not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.

STATIC (ESD) can damage PC boards.

DPut on grounded wrist strap BEFORE handling

boards or parts.

D Use proper static-proof bags and boxes to store, move, or ship PC boards.

H.F. RADIATION can cause interference.

DHigh frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment.

DHave only qualified persons familiar with elec- tronic equipment perform this installation.

DThe user is responsible for having a qualified electrician promptly correct any interference problem resulting from the installation.

DIf notified by the FCC about interference, stop using the equipment at once.

DHave the installation regularly checked and maintained.

DKeep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference.

EXPLODING HYDROGEN hazard.

DWhen cutting aluminum underwater or with the water touching the underside of the aluminum, free hydrogen gas may collect under the work- piece.

DSee your cutting engineer and water table instructions for help.

FALLING UNIT can cause injury.

DUse lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.

DUse equipment of adequate capacity to lift unit.

DIf using lift forks to move unit, be sure forks are long enough to ex- tend beyond opposite side of unit.

ARC CUTTING can cause interference.

DElectromagnetic energy can interfere with sensitive electronic equipment such as computers and computer-driven equipment such as robots.

DTo reduce possible interference, keep cables as short as possible, close together, and down low, such as on the floor.

DLocate cutting operation 100 meters from any sensitive electronic equipment.

DBe sure this cutting power source is installed and grounded according to this manual.

DIf interference still occurs, the user must take extra measures such as moving the machine, using shielded cables, using line filters, or shielding the work area.

1-4. California Proposition 65 Warnings

YWelding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some cases, cancer. (California Health & Safety Code Section 25249.5 et seq.)

YBattery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

For Gasoline Engines:

YEngine exhaust contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

For Diesel Engines:

YDiesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.

OM-2225 Page 3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Processes OM-2225190 009RDescription From Miller to You Table of Contents Page Cutting can cause fire or explosion Symbol UsageMarks a special safety message Plasma Arc Cutting HazardsNoise can damage hearing Exploding Parts can injureFlying Sparks can cause injury ARC Rays can burn eyes and skinCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers Identifie un message de sécurité particulier Signification des symbolesLE Coupage présente un risque de feu ou d’explosion UNE Décharge Électrique peut entraîner la mortLE Plasma D’ARC peut entraîner des blessures Risque de blessure en casLE Bruit peut endommager l’ouïe LES Fumées ET LES GAZ peuvent être dangereuxDES Particules Volantes peuvent blesser les yeux LES Bouteilles peuvent exploser si elles sont endommagéesDES Pieces Chaudes peuvent pro- voquer des brûlures graves DES Organes Mobiles peuvent provoquer des blessuresInformation sur les champs électromagnétiques Principales normes de sécuritéConsignes relatives aux stimulateurs cardiaques Specifications − InstallationDuty Cycle And Overheating Cutting Speed Movement Dimensions And WeightDo not move or operate unit where it could tip Selecting a LocationNormal Operating Connecting Work Clamp And Gas/Air SupplyElectrical Service Guide Input VoltageFor single-phase operation Connecting Input PowerAlways connect grounding Conductor first Controls − OperationSetting Gas/Air Pressure Setting Gas/Air PressureExample Of Cutting Operation Sequence Of OperationTrigger is pressed Months − Maintenance & TroubleshootingChecking Shield Cup Shutdown System Trouble LightsChecking/Replacing Retaining Cup, Tip, And Electrode Turn Off power source before checking torch partsTrouble Remedy TroubleshootingCircuit Diagram − Electrical Diagram− Parts List Complete Assembly PC3 Consumable Parts For ICE-80CX Torch, ICE-80CXTorch, ICE-80C XM Support ServiceMiller Electric Mfg. Co Owner’s Record

ICE-80CX, 3080 specifications

Miller Electric is renowned for producing high-quality welding equipment, and one of their standout products is the Miller Electric 3080, ICE-80CX. This portable welder is designed with both professional welders and hobbyists in mind, combining power, versatility, and ease of use in a compact package.

One of the main features of the ICE-80CX is its inverter technology, which allows for a lightweight design without compromising performance. Weighing significantly less than traditional welding machines, the ICE-80CX is easy to transport, making it suitable for a variety of job sites, from industrial applications to remote projects. The inverter technology also ensures efficient energy use, providing an excellent duty cycle while maintaining a stable arc.

The ICE-80CX offers the capability to TIG and stick weld, making it a versatile tool for welders who need to switch between different processes. This dual capability is complemented by an adjustable output range, which allows users to fine-tune the welding process according to the material being worked on and the thickness of the metal, ensuring optimal results in every application.

Another noteworthy characteristic of the ICE-80CX is its user-friendly interface. With intuitive controls, users can easily adjust settings such as amperage and voltage, allowing for quick adaptations to changing conditions. The digital display provides real-time feedback, helping welders monitor their performance and make necessary adjustments on the fly.

Durability is a hallmark of Miller Electric products, and the ICE-80CX is no exception. Built with robust materials and featuring protective casing, it is designed to withstand the rigors of the workplace. Additionally, the welder is equipped with advanced safety features, including thermal overload protection and a fault indicator, which enhance user safety and prolong the machine's lifespan.

Overall, the Miller Electric ICE-80CX is an exceptional welding machine that embodies the brand's commitment to innovation and quality. With its advanced inverter technology, dual welding capabilities, user-friendly interface, and durable design, it stands out as an excellent choice for anyone looking to achieve high-quality welds in a variety of settings. Whether for professional use or DIY projects, this welder offers a perfect blend of performance, reliability, and convenience.
Top Page Image Contents