Miller Electric S-74DX manual Directives, Standards

Page 4

Declaration of Conformity for

European Community (CE) Products

NOTE

This information is provided for units with CE certification (see rating label on unit).

Manufacturer:	European Contact:
Miller Electric Mg. Co.	Mr. Danilo Fedolfi,
1635 W. Spencer St.	Managing Director
Appleton, WI 54914 USA	ITW Welding Products Italy S.r.l.
Phone: (920) 734-9821	Via Privata Iseo 6/E
	20098 San Giuliano
	Milanese, Italy
	Phone: 39(02)98290-1
	Fax: 39(02)98290203

European Contact Signature:
Declares that the product:	S-74DX

conforms to the following Directives and Standards:

Directives

Low Voltage Directive: 73/23/EEC

Electromagnetic Compatibility (EMC) Directive: 89/336/EEC

Machinery Directives: 98/37/EEC, 91/368/EEC, 92/31/EEC, 133/04, 93/68/EEC

Standards

Arc Welding Equipment − Part 5: Wire Feeders. IEC 60974-5 Ed. 1

Arc Welding Equipment − Part 10: Electromagnetic Compatibility (EMC) Requirements. IEC 60974-10 August 2002

Arc Welding Equipment − Part 1: Welding Power Sources. IEC 60974-1 Ed. 2.1

Degrees Of Protection Provided By Enclosure (IP Code) IEC 60529 Ed. 2.1

Insulation Coordination For Equipment Within Low-Voltage Systems −

Part 1: Principles, Requirements and Tests: IEC 60664-1 Ed. 1.1

The product technical file is maintained by the responsible Business Unit(s) located at the manufacturing facility.

dec_wire_6/05

Image 4

Contents OM-1500-9 207 749K ProcessesDescription File MIG GmawFrom Miller to You Table of Contents Directives StandardsSymbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can killARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LES Fumées ET LES GAZ peuvent être dangereux UNE Décharge Électrique peut entraîner la mortIndique un message de sécurité particulier LE Soudage peut provoquer un Incendie ou une explosionDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sécurité En ce qui concerne les stimulateurs cardiaques+ + − DefinitionsSymbols And Definitions Rating Label For CE Products− Installation Specifications− Introduction Site SelectionRear Panel Connections And Rotating Drive Assembly Wire Type, Size, And Feed Speed Capability Table Motor Speed Wire Type Wire Size Feed Speed CapabilityPin Plug Information Gun Recommendation TableInstalling And Threading Welding Wire Extending from outlet wire guide asPosition Settings And Results For DIP Switch S1 Setting Internal DIP SwitchesDefining Motor Speed S1-7 Power Source Selection Menu Power Switch − OperationOperational Terms Program Push ButtonFront Panel Controls Wire SpeedTime sec Upper Display VoltsSetup Push Button Lower DisplayAdjust Control Sequence Push ButtonAuxiliary Menus Reset To Factory Settings Power Source Selection MenuTrigger Hold Setup Wire Feed Speed UnitsJog/Purge Software Revision LevelCode Display Hold− Setting Sequence Parameters Sequence Parameters In a Program− Setting Dual Schedule Parameters − MaintenanceOptional Dual Schedule Switch Diagrams Routine MaintenanceDiagnostics LED3-Related Error Indications− Electrical Diagram Circuit DiagramOM-1500-9 − Parts List Main AssemblyPart Description Quantity Control Box 207 Drive Assembly, Wire PLG5 Roll Kit Drive Roll Fraction Metric Drive Roll And Wire Guide KitsRoll Kit Drive Roll Work like a Pro Page Service SupportOwner’s Record Miller Electric Mfg. Co