Miller Electric S-74DX manual Setting Sequence Parameters, Sequence Parameters In a Program

Page 29

SECTION 7 − SETTING SEQUENCE PARAMETERS

7-1. Sequence Parameters In A Program

	Sequence		Parameters





		Volts	IPM	Seconds

1.	Preflow			0-9.9

2.	Run-In		X

3.	Start	X	X	0.00-5.00

4.	Weld	X	X	0-100.0

5.	Crater	X	X	0-5.00

6.	Burnback	X		0-0.25

7. Postflow				0-9.9

X = Setting available.

.For more information on

Sequence Push Button see Section 6-9.

If time is set to zero in Weld sequence, welding continues until gun trigger is released.

If time is set to zero in any timed sequence except Weld, the sequence is skipped.

				Weld Time
				Crater
				Time
					Burnback
		Start			Time
		Start
	Preflow	Time			Postflow
	Preflow				Postflow
	Time				Time
					Time
						Time
				Burnback		Sequence
Preflow	Run-In	Start	Weld	Crater	Postflow	Sequence
						End
Trigger				Trigger
Pressed				Released

OM-1500-9 Page 25

Image 29

Contents Processes OM-1500-9 207 749KDescription File MIG GmawFrom Miller to You Table of Contents Standards DirectivesMarks a special safety message Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux Incendie ou une explosion LE Soudage peut provoquer unDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU D’EXPLO’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresEn ce qui concerne les stimulateurs cardiaques Principales normes de sécurité− Definitions + +Rating Label For CE Products Symbols And DefinitionsSpecifications − Installation− Introduction Site SelectionRear Panel Connections And Rotating Drive Assembly Motor Speed Wire Type Wire Size Feed Speed Capability Wire Type, Size, And Feed Speed Capability TablePin Plug Information Gun Recommendation TableExtending from outlet wire guide as Installing And Threading Welding WireDefining Motor Speed S1-7 Setting Internal DIP SwitchesPosition Settings And Results For DIP Switch S1 Power Source Selection Menu − Operation Power SwitchOperational Terms Program Push ButtonTime sec Wire SpeedFront Panel Controls Volts Upper DisplayLower Display Setup Push ButtonSequence Push Button Adjust ControlAuxiliary Menus Power Source Selection Menu Reset To Factory SettingsTrigger Hold Setup Wire Feed Speed UnitsSoftware Revision Level Jog/PurgeCode Display HoldSequence Parameters In a Program − Setting Sequence Parameters− Maintenance − Setting Dual Schedule ParametersOptional Dual Schedule Switch Diagrams Routine MaintenanceLED3-Related Error Indications DiagnosticsCircuit Diagram − Electrical DiagramOM-1500-9 Main Assembly − Parts ListPart Description Quantity Control Box 207 Drive Assembly, Wire PLG5 Roll Kit Drive Roll Drive Roll And Wire Guide KitsRoll Kit Drive Roll Fraction Metric Work like a Pro Page Support ServiceMiller Electric Mfg. Co Owner’s Record

SECTION 7 − SETTING SEQUENCE PARAMETERS

7-1. Sequence Parameters In A Program

Sequence

IPM

.For more information on

Sequence Push Button see Section 6-9.