Miller Electric XLT 135, XLT 165, XLT 165, XLT 135 warranty Warranty

Page 47

Warranty

Effective January 1, 2000 (Equipment with a serial number preface of “LA” or newer)

This limited warranty supersedes all previous manufacturers warranties and is exclusive with no other guarantees or warranties expressed or implied.

LIMITED WARRANTY − Subject to the terms and conditions below, warrants to its original retail purchaser that new equipment sold after the effective date of this limited warranty is free of defects in material and workmanship at the time it is shipped from factory. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

Within the warranty periods listed below, manufacturer will repair or replace any warranted parts or components that fail due to such defects in material or workmanship. Manufacturer must be notified in writing within thirty (30) days of such defect or failure, at which time manufacturer will provide instructions on the warranty claim procedures to be followed.

Manufacturer shall honor warranty claims on warranted equipment listed below in the event of such a failure within the warranty time periods. All warranty time periods start on the date that the equipment was delivered to the original retail purchaser, or one year after the equipment is sent to the distributor.

1.5 Years Parts − 3 Years Labor

*Original main power rectifiers

2.3 Years — Parts and Labor

*Transformer/Rectifier Power Sources

*Plasma Arc Cutting Power Sources

*Semi-Automatic and Automatic Wire Feeders

*Engine Driven Welding Generators

(NOTE: Engines are warranted separately by the engine manufacturer.)

3.1 Year — Parts and Labor

*Motor Driven Guns (w/exception of Spoolmate 185)

*Process Controllers

*Positioners and Controllers

*Automatic Motion Devices

*Robots

*RFCS Foot Controls

*Induction Heating Power Sources

*Water Coolant Systems

*HF Units

*Grids

*Spot Welders

*Load Banks

*SDX Transformers

*Running Gear/Trailers

*Field Options

(NOTE: Field options are covered under the limited warranty for the remaining warranty period of the product they are installed in, or for a minimum of one year — whichever is greater.)

4.6 Months — Batteries

5.90 Days — Parts and Labor

*MIG Guns/TIG Torches

*Induction Heating Coils and Blankets

*Plasma Cutting Torches

*Remote Controls

*Accessory Kits

*Replacement Parts

*Spoolmate 185

Limited Warranty shall not apply to:

1.Items furnished by manufacturer, but manufactured by others, such as engines or trade accessories. These items are covered by the manufacturer’s warranty, if any.

2.Consumable components; such as contact tips, cutting nozzles, contactors, relays, brushes, slip rings, or parts that fail due to normal wear.

3.Equipment that has been modified by any party other than manufacturer, or equipment that has been improperly installed, improperly operated or misused based upon industry standards, or equipment which has not had reasonable and necessary maintenance, or equipment which has been used for operation outside of the specifications for the equipment.

MANUFACTURER’S PRODUCTS ARE INTENDED FOR PURCHASE AND USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS TRAINED AND EXPERIENCED IN THE USE AND MAINTENANCE OF WELDING EQUIPMENT.

In the event of a warranty claim covered by this warranty, the exclusive remedies shall be, at manufacturers option: (1) repair; or (2) replacement; or, where authorized in writing by manufacturer in appropriate cases, (3) the reasonable cost of repair or replacement at an authorized service station; or

(4)payment of or credit for the purchase price (less reasonable depreciation based upon actual use) upon return of the goods at customer’s risk and expense. manufacturer’s option of repair or replacement will be F.O.B., Factory at Appleton, Wisconsin, or F.O.B. at an authorized service facility as determined by manufacturer. Therefore no compensation or reimbursement for transportation costs of any kind will be allowed.

TO THE EXTENT PERMITTED BY LAW, THE REMEDIES PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE REMEDIES. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF PROFIT), WHETHER BASED ON CONTRACT, TORT OR ANY OTHER LEGAL THEORY.

ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND ANY IMPLIED WARRANTY, GUARANTY OR REPRESENTATION AS TO PERFORMANCE, AND ANY REMEDY FOR BREACH OF CONTRACT TORT OR ANY OTHER LEGAL THEORY WHICH, BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION, OPERATION OF LAW, CUSTOM OF TRADE OR COURSE OF DEALING, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, WITH RESPECT TO ANY AND ALL EQUIPMENT FURNISHED BY MANUFACTURER IS EXCLUDED AND DISCLAIMED BY MANUFACTURER.

Some states in the U.S.A. do not allow limitations of how long an implied warranty lasts, or the exclusion of incidental, indirect, special or consequential damages, so the above limitation or exclusion may not apply to you. This warranty provides specific legal rights, and other rights may be available, but may vary from state to state.

In Canada, legislation in some provinces provides for certain additional warranties or remedies other than as stated herein, and to the extent that they may not be waived, the limitations and exclusions set out above may not apply. This Limited Warranty provides specific legal rights, and other rights may be available, but may vary from province to province.

brand_warr 1/00

Image 47
Contents April OM-198 076AProcesses DescriptionPage Table of Contents Page Electric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesPrincipal Safety Standards About Pacemakers EMF InformationLES Fumées ET LES GAZ peuvent être dangereux Signification des symboles− Consignes DE Securite − Lire Avant Utilisation UN Choc Électrique peut tuerLE Bruit peut affecter l’ouïe LE Soudage peut provoquer un incendie ou une explosionDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent pro- voquer des brûlures gravesDES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OULA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peutConsignes relatives aux stimulateurs cardiaques Principales normes de sécuritéInformation sur les champs électromagnétiques VAC Model − SpecificationsSpecifications Overheating Duty Cycle And OverheatingOutput Duty Cycle % Output AmperesVolt-Ampere Curves Installing Welding Gun Installing Work Clamp − InstallationChanging Polarity Process/Polarity TableRegulator/flowmeter and CO2 cylinder CO2 Gas Installing Gas SupplyFlow Adjust CO2 Adapter Customer Sup- pliedUp to 200 ft 61 m Rating LabelGrounded Receptacle Volt, 20 ampere individualSee Section Do not move or operate unit where it could tipPlug ReceptacleAdjusting Hub Tension Electrical Service Guide For 230 VAC ModelInstalling Wire Spool And Adjusting Hub Tension Standard Wire Spool 8 Lb Wire Spool 4Threading Welding Wire Controls Voltage SwitchPower Switch OM-198 076 − OperationWeld Parameters For 115 VAC Model Weld Parameters For 230 VAC Model Drive Motor Protection − Maintenance &TROUBLESHOOTINGRoutine Maintenance Overload ProtectionReplacing Gun Contact Tip Changing Drive Roll Or Wire Inlet GuideTurn Off power before replacing contact tip To Reassemble Gun Cleaning Or Replacing Gun LinerDisconnect gun from unit Replacing Switch And/Or Head Tube Does not run Troubleshooting TableTrouble Remedy Circuit Diagram For 115 VAC Model − Electrical DiagramCircuit Diagram For 230 VAC Model Typical MIG Process Connections − MIG Welding Gmaw GuidelinesSelect Voltage Typical MIG Process Control SettingsWire Size Amperage Range Select Wire Size Recommendation Wire SpeedHolding And Positioning Welding Gun ShortNormalLong Conditions That Affect Weld Bead ShapePush Perpendicular Drag Short Normal LongGun Movement During Welding Poor Weld Bead CharacteristicsGood Weld Bead Characteristics Possible Causes Corrective Actions Troubleshooting − Excessive SpatterTroubleshooting − Porosity Troubleshooting − Excessive PenetrationTroubleshooting − Burn-Through Troubleshooting − Lack Of PenetrationTroubleshooting − Incomplete Fusion Direction Troubleshooting − Waviness Of BeadTroubleshooting − Distortion Base metal to moveFlat & Horizontal1 Fillet Common MIG Shielding GasesApplication Main Assembly − Parts ListDia Part Description Quantity Mkgs Gun 024 .6 and .045 042024 .6 and .030/.035 .8 Page Warranty Owner’s Record