Miller Electric 652 Tipping, VAC Receptacle And Supplementary Protectors, Weld Output Terminals

Page 22

.A complete Parts List is available at www.MillerWelds.com

4-6. Tipping

! Be careful when placing or moving unit over uneven surfaces.

4-7. 115 VAC Receptacle And Supplementary Protectors

! Turn Off power before connecting to receptacle.

1115 V 15 A AC Receptacle RC9

Power is shared between RC9 and Remote 14 receptacle RC8 (see Section 4-15).

2Supplementary Protector CB1

3Supplementary Protector CB2

CB1 protects the 115 volts ac por- tion of RC8 and RC9 from overload.

CB2 protects the 24 volts ac portion of RC8 and Remote Power On/Off from overload.

Press button to reset protector.

Ref. 800 166-D

4-8. Weld Output Terminals

! Turn Off power before connecting to weld output terminals

1 Positive High Inductance Terminal

2 Positive Low Inductance Terminal

3 Negative Weld Outout Terminal

See Sections 4-11, 4-12or 4-13 .

1	2

Ref. 800 166-D

OM-278 Page 14

Image 22

Contents Description ProcessesFile Multi-Process From Miller to You Table of Contents Standards DirectivesDecstat6/05 Electric Shock can kill Symbol UsageArc Welding Hazards HOT Parts can cause severe burnsWelding can cause fire or explosion Fumes and Gases can be hazardousARC Rays can burn eyes and skin Flying Metal or Dirt can injure eyesFalling Unit can cause injury Welding Wire can cause injuryFire or Explosion hazard Moving Parts can cause injuryEMF Information Principal Safety StandardsCalifornia Proposition 65 Warnings About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion Risque D’INCENDIE OU D’EXPLO- Sion LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées LA Chute DE L’APPAREIL peut blesserLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-278 General Precautionary Label − DefinitionsElectric Shock And Airflow Label Nameplate Safety SymbolsInput Connection Label ? aManufacturer’s Rating Label For CE Products Weee Label For Products Sold Within The EUSymbols And Definitions − InstallationSpecifications Volt-Ampere Curves CC Mode CV ModeDuty Cycle And Overheating 100% Duty CycleMovement Location And Airflow Selecting a Location460 mm OM-278 Weight Dimensions And WeightsDimensions Holes FrontVAC Receptacle And Supplementary Protectors TippingWeld Output Terminals Connecting Weld Output Cables Selecting Cable SizesMig Gmaw Cable Connections Gas Flowmeter RegulatorMig Gmaw And Flux Cored Fcaw Cable Connections Turn Off power before making connectionsRear Wire Feeder Fcaw GaslessRemote 14 Receptacle RC8 Information To remote On/Off switchTIG Gtaw Cable Connections InformationConnecting Remote Control Electrical Service GuidePlacing Jumper Links Tools Needed Do not overtighten Jumper link nutsDisconnect Device Input Power Connec- tions Connecting Input PowerWelding Power Source Input Power Con- nections = GND/PE Earth Ground− Operation Controls Non CE ModelsControls CE Models Fuse F1 − Maintenance & TroubleshootingRoutine Maintenance Short Circuit ShutdownTroubleshooting Trouble Remedy− Electrical Diagram Circuit Diagram218 514-B Recommended Spare Parts − Parts ListRecommended Spare Parts Page Page Your distributor also gives ServiceSupport For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s