Miller Electric 812, 652 manual Mig Gmaw And Flux Cored Fcaw Cable Connections, Fcaw Gasless

Page 25

. A complete Parts List is available at www.MillerWelds.com

4-12. Mig (GMAW) And Flux Cored (FCAW) Cable Connections

GMAW / FCAW

Gas Flowmeter/

Regulator

HIGHLOW

INDUCTANCE INDUCTANCE (Gasless FCAW)

−

! Turn Off power before making connections.

.For better performance for most GMAW and (gas shielded)

FCAW (DCEP) applications, it is recommended that weld output connections be made to the Low Inductance weld output terminal. Make connections as shown.

Rear Of

Wire Feeder

FCAW (Gasless)

LOW INDUCTANCE (Gasless FCAW)

−

Rear Of

Wire Feeder

! Turn Off power before making connections.

.For better performance for most Gasless Flux Cored FCAW

(DCEN) applications, it is recommended that weld output connections be made to the Low Inductance weld output ter- minal. Make connections as shown.

OM-278 Page 17

Image 25

Contents Description ProcessesFile Multi-Process From Miller to You Table of Contents Standards DirectivesDecstat6/05 Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burnsARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyesFire or Explosion hazard Welding Wire can cause injuryFalling Unit can cause injury Moving Parts can cause injuryCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical DevicesUNE Décharge Électrique peut entraîner la mort Symboles utilisésLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-278 − Definitions General Precautionary LabelInput Connection Label Nameplate Safety SymbolsElectric Shock And Airflow Label ? aWeee Label For Products Sold Within The EU Manufacturer’s Rating Label For CE ProductsSymbols And Definitions − InstallationSpecifications Duty Cycle And Overheating CC Mode CV ModeVolt-Ampere Curves 100% Duty CycleMovement Location And Airflow Selecting a Location460 mm OM-278 Dimensions Dimensions And WeightsWeight Holes FrontVAC Receptacle And Supplementary Protectors TippingWeld Output Terminals Selecting Cable Sizes Connecting Weld Output CablesGas Flowmeter Regulator Mig Gmaw Cable ConnectionsRear Wire Feeder Turn Off power before making connectionsMig Gmaw And Flux Cored Fcaw Cable Connections Fcaw GaslessTIG Gtaw Cable Connections To remote On/Off switchRemote 14 Receptacle RC8 Information InformationElectrical Service Guide Connecting Remote ControlTools Needed Do not overtighten Jumper link nuts Placing Jumper LinksWelding Power Source Input Power Con- nections Connecting Input PowerDisconnect Device Input Power Connec- tions = GND/PE Earth GroundControls Non CE Models − OperationControls CE Models Routine Maintenance − Maintenance & TroubleshootingFuse F1 Short Circuit ShutdownTrouble Remedy TroubleshootingCircuit Diagram − Electrical Diagram218 514-B Recommended Spare Parts − Parts ListRecommended Spare Parts Page Page Your distributor also gives ServiceSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s