Miller Electric 652, 812 manual Directives, Standards, Decstat6/05

Page 4

Declaration of Conformity for

European Community (CE) Products

NOTE

This information is provided for units with CE certification (see rating label on unit).

Manufacturer:	European Contact:
Miller Electric Mg. Co.	Mr. Danilo Fedolfi,
1635 W. Spencer St.	Managing Director
Appleton, WI 54914 USA	ITW Welding Products Italy S.r.l.
Phone: (920) 734-9821	Via Privata Iseo 6/E
	20098 San Giuliano
	Milanese, Italy
	Phone: 39(02)98290-1
	Fax: 39(02)98290203

European Contact Signature:

Declares that the product: Dimension™ 812

conforms to the following Directives and Standards:

Directives

Electromagnetic compatibility Directives: 89/336/EEC, 92/31/EEC

Low Voltage Directive: 73/23/EEC

Machinery Directives: 89/392/EEC, 91/368/EEC, 93/C 133/04, 93/68/EEC

Standards

Safety Requirements for Arc Welding Equipment part 1: EN 60974-1: 1990

Arc Welding Equipment Part 1: Welding Power Sources: IEC 974-1

(April 1995 − Draft revision)

Degrees of Protection provided by Enclosures (IP code): IEC 529: 1989

Insulation coordination for equipment within low-voltage systems:

Part 1: Principles, requirements and tests: IEC 664-1: 1992

Electromagnetic compatibility (EMC) Product standard for arc welding equipment:

EN50199: August 1995

dec_stat_6/05

Image 4

Contents Description ProcessesFile Multi-Process From Miller to You Table of Contents Standards DirectivesDecstat6/05 Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burnsFumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyesWelding Wire can cause injury Fire or Explosion hazardFalling Unit can cause injury Moving Parts can cause injuryPrincipal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-278 General Precautionary Label − DefinitionsNameplate Safety Symbols Input Connection LabelElectric Shock And Airflow Label ? aManufacturer’s Rating Label For CE Products Weee Label For Products Sold Within The EUSymbols And Definitions − InstallationSpecifications CC Mode CV Mode Duty Cycle And OverheatingVolt-Ampere Curves 100% Duty CycleMovement Location And Airflow Selecting a Location460 mm OM-278 Dimensions And Weights DimensionsWeight Holes FrontVAC Receptacle And Supplementary Protectors TippingWeld Output Terminals Connecting Weld Output Cables Selecting Cable SizesMig Gmaw Cable Connections Gas Flowmeter RegulatorTurn Off power before making connections Rear Wire FeederMig Gmaw And Flux Cored Fcaw Cable Connections Fcaw GaslessTo remote On/Off switch TIG Gtaw Cable ConnectionsRemote 14 Receptacle RC8 Information InformationConnecting Remote Control Electrical Service GuidePlacing Jumper Links Tools Needed Do not overtighten Jumper link nutsConnecting Input Power Welding Power Source Input Power Con- nectionsDisconnect Device Input Power Connec- tions = GND/PE Earth Ground− Operation Controls Non CE ModelsControls CE Models − Maintenance & Troubleshooting Routine MaintenanceFuse F1 Short Circuit ShutdownTroubleshooting Trouble Remedy− Electrical Diagram Circuit Diagram218 514-B Recommended Spare Parts − Parts ListRecommended Spare Parts Page Page Your distributor also gives ServiceSupport To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s