Miller Electric 852 manual Symbols And Definitions, Weee Label For Products Sold Within The EU

Page 16

.A complete Parts List is available at www.MillerWelds.com

3-6. Symbols And Definitions

Note Some symbols are found only on CE products.

A

Amperes

Amperage Control/

Gas Tungsten Arc

Shielded Metal Arc

Panel

Welding (GTAW)

Welding (SMAW)

Temperature

Do Not Switch

Arc Force (DIG)

Percent

While Welding

Output

Circuit Breaker

Remote

V

Volts

Protective Earth

Positive

Negative

Input

(Ground)

On

Off

Hz

Hertz

Direct Current

U0

Rated No Load

U1

Primary Voltage

U2

Conventional Load

Line Connection

Voltage (Average)

Voltage

I1

I2

Rated Welding

X

Three-Phase

Primary Current

Current

Duty Cycle

Transformer

Rectifier

IP

Degree Of

Three-Phase

S1

KVA

Work Connection

Protection

Wire Feeder

Electrode

Connection

3-7. WEEE Label (For Products Sold Within The EU)

Do not discard product (where ap- plicable) with general waste.

Reuse or recycle Waste Electrical and Electronic Equipment (WEEE) by disposing at a designated collec- tion facility.

Contact your local recycling office or your local distributor for further information.

OM-222 Page 12

Image 16

Contents Description ProcessesFile Stick Smaw From Miller to You Table of Contents Directives StandardsSymbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can killARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers Signification des symboles − Consignes DE Sécurité − À Lire Avant UtilisationLES Décharges Électriques peuvent être mortelles LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut causer un incen- die ou une explosion LES Particules Projetées peu- vent blesser les yeuxLES Pièces Chaudes peuvent cau- ser des brûlures graves LE Bruit peut affecter l’ouïeRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut Faire LES Pièces Mobiles peuvent cau- ser des blessuresInformation sur les champs électromagnétiques Principales normes de sécuritéConsignes relatives aux stimulateurs cardiaques General Precautionary Label − DefinitionsNameplate Safety Symbols Input Connection LabelElectric Shock And Airflow Label ? aManufacturer’s Rating Labels For CE Products Symbols And Definitions Weee Label For Products Sold Within The EU− Installation SpecificationsDuty Cycle And Overheating 200 230 380 400 440 460 575Volt-Ampere Curves Amp ModelSelecting a Location MovementDimensions Amp Models Dimensions And WeightsWeight Be careful when placing or moving unit over uneven surfaces Turn Off power before connecting to receptacleTipping VAC Receptacle And Supplementary ProtectorsConnecting Weld Output Cables Weld Output Terminals And Selecting Cable SizesConnecting Remote Control Remote 14 Receptacle InformationInformation To remote On/O ff sw itchElectrical Service Guide Placing Jumper Links Welding Power Source Input Power Connections Connecting Input PowerDisconnect Device Input Power Con- nections Turn Off Power before reversing cables Turn Off power before connecting re- mote device− Operation Controls Non CE Models− Maintenance and Troubleshooting Routine MaintenanceDisconnect power before maintaining Months Controls CE ModelsFuse F1 TroubleshootingTrouble Remedy − Electrical Diagram Circuit Diagram218 518-A − Parts List Page Page Service SupportOwner’s Record Miller Electric Mfg. Co