Miller Electric 852 manual ARC Rays can burn eyes and skin, Welding can cause fire or explosion

Page 6

ARC RAYS can burn eyes and skin.

Arc rays from the welding process produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin. Sparks fly off from the weld.

DWear an approved welding helmet fitted with a proper shade of fil- ter lenses to protect your face and eyes when welding or watching (see ANSI Z49.1 and Z87.1 listed in Safety Standards).

DWear approved safety glasses with side shields under your helmet.

DUse protective screens or barriers to protect others from flash, glare and sparks; warn others not to watch the arc.

DWear protective clothing made from durable, flame-resistant mate- rial (leather, heavy cotton, or wool) and foot protection.

WELDING can cause fire or explosion.

Welding on closed containers, such as tanks, drums, or pipes, can cause them to blow up. Sparks can fly off from the welding arc. The flying sparks, hot workpiece, and hot equipment can cause fires and

burns. Accidental contact of electrode to metal objects can cause sparks, explosion, overheating, or fire. Check and be sure the area is safe before doing any welding.

DRemove all flammables within 35 ft (10.7 m) of the welding arc. If this is not possible, tightly cover them with approved covers.

DDo not weld where flying sparks can strike flammable material.

DProtect yourself and others from flying sparks and hot metal.

DBe alert that welding sparks and hot materials from welding can easily go through small cracks and openings to adjacent areas.

DWatch for fire, and keep a fire extinguisher nearby.

DBe aware that welding on a ceiling, floor, bulkhead, or partition can cause fire on the hidden side.

DDo not weld on closed containers such as tanks, drums, or pipes, unless they are properly prepared according to AWS F4.1 (see Safety Standards).

DConnect work cable to the work as close to the welding area as practical to prevent welding current from traveling long, possibly unknown paths and causing electric shock, sparks, and fire hazards.

DDo not use welder to thaw frozen pipes.

DRemove stick electrode from holder or cut off welding wire at contact tip when not in use.

DWear oil-free protective garments such as leather gloves, heavy shirt, cuffless trousers, high shoes, and a cap.

DRemove any combustibles, such as a butane lighter or matches, from your person before doing any welding.

DFollow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B for hot work and have a fire watcher and extinguisher nearby.

FLYING METAL can injure eyes.

DWelding, chipping, wire brushing, and grinding cause sparks and flying metal. As welds cool, they can throw off slag.

DWear approved safety glasses with side shields even under your welding helmet.

BUILDUP OF GAS can injure or kill.

DShut off shielding gas supply when not in use.

D Always ventilate confined spaces or use approved air-supplied respirator.

HOT PARTS can cause severe burns.

DDo not touch hot parts bare handed.

DAllow cooling period before working on gun or

torch.

DTo handle hot parts, use proper tools and/or wear heavy, insulated welding gloves and clothing to prevent burns.

MAGNETIC FIELDS can affect pacemakers.

D Pacemaker wearers keep away.

D Wearers should consult their doctor before going near arc welding, gouging, or spot welding operations.

NOISE can damage hearing.

Noise from some processes or equipment can damage hearing.

DWear approved ear protection if noise level is high.

CYLINDERS can explode if damaged.

Shielding gas cylinders contain gas under high pressure. If damaged, a cylinder can explode. Since gas cylinders are normally part of the welding process, be sure to treat them carefully.

DProtect compressed gas cylinders from excessive heat, mechani- cal shocks, physical damage, slag, open flames, sparks, and arcs.

DInstall cylinders in an upright position by securing to a stationary support or cylinder rack to prevent falling or tipping.

DKeep cylinders away from any welding or other electrical circuits.

DNever drape a welding torch over a gas cylinder.

DNever allow a welding electrode to touch any cylinder.

DNever weld on a pressurized cylinder − explosion will result.

DUse only correct shielding gas cylinders, regulators, hoses, and fit- tings designed for the specific application; maintain them and associated parts in good condition.

DTurn face away from valve outlet when opening cylinder valve.

DKeep protective cap in place over valve except when cylinder is in use or connected for use.

DUse the right equipment, correct procedures, and sufficient num- ber of persons to lift and move cylinders.

DRead and follow instructions on compressed gas cylinders, associated equipment, and Compressed Gas Association (CGA) publication P-1 listed in Safety Standards.

OM-222 Page 2

Image 6
Contents Processes DescriptionFile Stick Smaw From Miller to You Table of Contents Directives StandardsArc Welding Hazards Symbol UsageMarks a special safety message Electric Shock can killFlying Metal can injure eyes ARC Rays can burn eyes and skinWelding can cause fire or explosion Buildup of GAS can injure or killCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers LES Décharges Électriques peuvent être mortelles Signification des symboles− Consignes DE Sécurité − À Lire Avant Utilisation LES Fumées ET LES GAZ peuvent être dangereuxLES Pièces Chaudes peuvent cau- ser des brûlures graves LE Soudage peut causer un incen- die ou une explosionLES Particules Projetées peu- vent blesser les yeux LE Bruit peut affecter l’ouïe’EMPLOI Excessif peut Faire Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser LES Pièces Mobiles peuvent cau- ser des blessuresPrincipales normes de sécurité Information sur les champs électromagnétiquesConsignes relatives aux stimulateurs cardiaques General Precautionary Label − DefinitionsElectric Shock And Airflow Label Nameplate Safety SymbolsInput Connection Label ? aManufacturer’s Rating Labels For CE Products Symbols And Definitions Weee Label For Products Sold Within The EUDuty Cycle And Overheating − InstallationSpecifications 200 230 380 400 440 460 575Volt-Ampere Curves Amp ModelSelecting a Location MovementDimensions And Weights Dimensions Amp ModelsWeight Tipping Be careful when placing or moving unit over uneven surfacesTurn Off power before connecting to receptacle VAC Receptacle And Supplementary ProtectorsConnecting Weld Output Cables Weld Output Terminals And Selecting Cable SizesInformation Connecting Remote ControlRemote 14 Receptacle Information To remote On/O ff sw itchElectrical Service Guide Placing Jumper Links Connecting Input Power Welding Power Source Input Power ConnectionsDisconnect Device Input Power Con- nections − Operation Turn Off Power before reversing cablesTurn Off power before connecting re- mote device Controls Non CE ModelsDisconnect power before maintaining Months − Maintenance and TroubleshootingRoutine Maintenance Controls CE ModelsTroubleshooting Fuse F1Trouble Remedy − Electrical Diagram Circuit Diagram218 518-A − Parts List Page Page Service SupportOwner’s Record Miller Electric Mfg. Co