Miller Electric 852 manual Directives, Standards

Page 4

Declaration of Conformity for

European Community (CE) Products

NOTE

This information is provided for units with CE certification (see rating label on unit).

Manufacturer:	European Contact:
Miller Electric Mg. Co.	Mr. Danilo Fedolfi,
1635 W. Spencer St.	Managing Director
Appleton, WI 54914 USA	ITW Welding Products Italy S.r.l.
Phone: (920) 734-9821	Via Privata Iseo 6/E
	20098 San Giuliano
	Milanese, Italy
	Phone: 39(02)98290-1
	Fax: 39(02)98290203

European Contact Signature:

Declares that the product: Goldstar→ 402, 602, And 852

conforms to the following Directives and Standards:

Directives

Electromagnetic compatibility Directives: 89/336/EEC, 92/31/EEC

Low Voltage Directive: 73/23/EEC

Machinery Directives: 89/392/EEC, 91/368/EEC, 93/C 133/04, 93/68/EEC

Standards

Safety Requirements for Arc Welding Equipment part 1: EN 60974-1: 1990

Arc Welding Equipment Part 1: Welding Power Sources: IEC 974-1

(April 1995 − Draft revision)

Degrees of Protection provided by Enclosures (IP code): IEC 529: 1989

Insulation coordination for equipment within low-voltage systems:

Part 1: Principles, requirements and tests: IEC 664-1: 1992

Electromagnetic compatibility (EMC) Product standard for arc welding equipment:

EN50199: August 1995

dec_stat_6/05

Image 4

Contents Description ProcessesFile Stick Smaw From Miller to You Table of Contents Directives StandardsSymbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can killARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers Signification des symboles − Consignes DE Sécurité − À Lire Avant UtilisationLES Décharges Électriques peuvent être mortelles LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut causer un incen- die ou une explosion LES Particules Projetées peu- vent blesser les yeuxLES Pièces Chaudes peuvent cau- ser des brûlures graves LE Bruit peut affecter l’ouïeRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut Faire LES Pièces Mobiles peuvent cau- ser des blessuresInformation sur les champs électromagnétiques Principales normes de sécuritéConsignes relatives aux stimulateurs cardiaques General Precautionary Label − DefinitionsNameplate Safety Symbols Input Connection LabelElectric Shock And Airflow Label ? aManufacturer’s Rating Labels For CE Products Symbols And Definitions Weee Label For Products Sold Within The EU− Installation SpecificationsDuty Cycle And Overheating 200 230 380 400 440 460 575Volt-Ampere Curves Amp ModelSelecting a Location MovementDimensions Amp Models Dimensions And WeightsWeight Be careful when placing or moving unit over uneven surfaces Turn Off power before connecting to receptacleTipping VAC Receptacle And Supplementary ProtectorsConnecting Weld Output Cables Weld Output Terminals And Selecting Cable SizesConnecting Remote Control Remote 14 Receptacle InformationInformation To remote On/O ff sw itchElectrical Service Guide Placing Jumper Links Welding Power Source Input Power Connections Connecting Input PowerDisconnect Device Input Power Con- nections Turn Off Power before reversing cables Turn Off power before connecting re- mote device− Operation Controls Non CE Models− Maintenance and Troubleshooting Routine MaintenanceDisconnect power before maintaining Months Controls CE ModelsFuse F1 TroubleshootingTrouble Remedy − Electrical Diagram Circuit Diagram218 518-A − Parts List Page Page Service SupportOwner’s Record Miller Electric Mfg. Co