Miller Electric 852 manual Remote 14 Receptacle Information, Connecting Remote Control

Page 23

		. A complete Parts List is available at www.MillerWelds.com
4-10. Remote 14 Receptacle Information
	Socket	Information
	A	24 volts ac. Protected by supplementary protector CB2.
24 VOLTS AC	B	Contact closure to A completes 24 volts ac contactor control circuit.
	B
	C	Command reference; 0 to +10 volts dc.
REMOTE OUTPUT CONTROL	D	Remote control circuit common.

		E	0 to +10 volts dc input command signal from remote control.
		F	Current feedback; 1 volt per 100 amperes.
		H	Voltage feedback; 1 volt per 10 arc volts.
		I	115 volts, 15 amperes, 60 Hz ac. Protected by supplementary protector CB1.
	115 VOLTS AC	J	Contact closure to I completes 115 volts ac contactor control circuit.
		J
	GND	K	Chassis common.
	GND	G	Circuit common for 24 and 115 volts ac circuits.
		G	Circuit common for 24 and 115 volts ac circuits.
	REMOTE POWER ON/OFF	*	To remote On/Off switch.
	REMOTE POWER ON/OFF	*	To remote On/Off switch.
		*
	REMOTE VOLTAGE SENSING	*	Voltage sensing signal from Negative (-) weld output terminal.
	REMOTE VOLTAGE SENSING	*	Voltage sensing signal from Positive (+) weld output terminal.
		*
	* Not Used

4-11. Connecting Remote Control

1 Remote 14 Receptacle RC8 Connect remote control to RC8.

1

A K		J I
B
C	L N	H
D	M	G
	E	F

OR

OR

Ref. ST-800 101-D / ST-141 127-D

OM-222 Page 19

Image 23

Contents File Stick Smaw ProcessesDescription From Miller to You Table of Contents Standards DirectivesElectric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information LES Fumées ET LES GAZ peuvent être dangereux Signification des symboles− Consignes DE Sécurité − À Lire Avant Utilisation LES Décharges Électriques peuvent être mortellesLE Bruit peut affecter l’ouïe LE Soudage peut causer un incen- die ou une explosionLES Particules Projetées peu- vent blesser les yeux LES Pièces Chaudes peuvent cau- ser des brûlures gravesLES Pièces Mobiles peuvent cau- ser des blessures Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peut FaireConsignes relatives aux stimulateurs cardiaques Principales normes de sécuritéInformation sur les champs électromagnétiques − Definitions General Precautionary Label? a Nameplate Safety SymbolsInput Connection Label Electric Shock And Airflow LabelManufacturer’s Rating Labels For CE Products Weee Label For Products Sold Within The EU Symbols And Definitions200 230 380 400 440 460 575 − InstallationSpecifications Duty Cycle And OverheatingAmp Model Volt-Ampere CurvesMovement Selecting a LocationWeight Dimensions And WeightsDimensions Amp Models VAC Receptacle And Supplementary Protectors Be careful when placing or moving unit over uneven surfacesTurn Off power before connecting to receptacle TippingWeld Output Terminals And Selecting Cable Sizes Connecting Weld Output CablesTo remote On/O ff sw itch Connecting Remote ControlRemote 14 Receptacle Information InformationElectrical Service Guide Placing Jumper Links Disconnect Device Input Power Con- nections Connecting Input PowerWelding Power Source Input Power Connections Controls Non CE Models Turn Off Power before reversing cablesTurn Off power before connecting re- mote device − OperationControls CE Models − Maintenance and TroubleshootingRoutine Maintenance Disconnect power before maintaining MonthsTrouble Remedy TroubleshootingFuse F1 Circuit Diagram − Electrical Diagram218 518-A − Parts List Page Page Support ServiceMiller Electric Mfg. Co Owner’s Record