Bosch Power Tools 11222EVSG manual Maintenance, Accessories, Cleaning

Page 9
! WARNING
! WARNING

BM 1619929320 2/03 2/12/03 9:42 AM Page 9

Maintenance

Service

!WARNING Preventive maintenance

performed by unauth- orized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service be performed by a Bosch Factory Service Center or Authorized Bosch Service Station.

SERVICE REMINDER LIGHT

When the service reminder light lights up or blinks, this will indicate that the cut-out carbon brushes will switch off the tool in approximately 8 hours. After that period, the light will go off and the tool will stop running. The tool must then be sent to a service center for service.

TOOL LUBRICATION

Your Bosch tool has been properly lubricated and is ready to use. It is recommended that tools with gears be regreased with a special gear lubricant at every brush change.

CARBON BRUSHES

The brushes and commutator in your tool have been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend every two to six months the brushes be examined. Only genuine Bosch replacement

brushes specially designed for your tool should be used.

BEARINGS

Every second brush change, the bearings should be replaced at Bosch Factory Service Center or Authorized Bosch Service Station. Bearings which become noisy (due to heavy load or very abrasive material cutting) should be replaced at once to avoid overheating or motor failure.

Cleaning

To avoid accidents always disconnect the tool from the power supply before cleaning or

performing any maintenance. The tool may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through openings.

Certain cleaning agents ! CAUTION and solvents damage

plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

Accessories

If an extension cord is necessary, a cord with adequate size conductors that is capable

of carrying the current necessary for your tool must be used. This will prevent excessive voltage drop, loss of power or overheating. Grounded tools must use 3- wire extension cords that have 3-prong plugs and receptacles.

NOTE: The smaller the gauge number, the heavier the cord.

RECOMMENDED SIZES OF EXTENSION CORDS

120 VOLT ALTERNATING CURRENT TOOLS

Tool’s

Cord Size in A.W.G.

Wire Sizes in mm2

Ampere

 

 

 

 

 

 

 

 

Cord Length in Feet

Cord Length in Meters

Rating

 

25

50

100

150

15

30

60

120

3-6

 

 

 

 

 

 

 

 

18

16

16

14

.75

.75

1.5

2.5

6-8

18

16

14

12

.75

1.0

2.5

4.0

8-10

18

16

14

12

.75

1.0

2.5

4.0

10-12

16

16

14

12

1.0

2.5

4.0

12-16

14

12

 

 

 

 

 

 

 

 

 

* Auxiliary Handle

(*= standard equipment)

* Depth gauge

(**= optional accessories)

* Carrying case

 

-9-

Image 9
Contents Seguridad 11222EVSG Read Before Using Lire avant usage Leer antes de usarElectrical Safety Power Tool Safety RulesPersonal Safety Work AreaRotary Hammer Safety Rules ServiceTool Use and Care BM 1619929320 2/03 2/12/03 942 AM Symbols Rotary Hammer Functional Description and SpecificationsOperating Instructions Selector Dial VARIO-LOCK Selector DialQuick Change SDS TOOL-HOLDER Slip ClutchMaintenance AccessoriesCleaning Aire de travail Règles de Sécurité GénéralesSécurité électrique Sécurité des personnesRéparation Règles de sécurité concernant les marteaux rotatifsPeuvent être chauds après une utilisation prolongée Ni-Cad SymbolesMarteau rotatif Description fonctionnelle et spécificationsConsignes de fonctionnement Cadran Sélecteur « VARIO-LOCK » Cadran SélecteurDouille DE Retenue SDS À Changement Rapide Accouplement À GlissementEntretien AccessoiresArea de trabajo Normas de seguridad para herramientas mecánicasSeguridad eléctrica Seguridad personalServicio Normas de seguridad para martillos giratoriosBM 1619929320 2/03 2/12/03 942 AM De Ni-Cd SímbolosMartillo giratorio Descripción funcional y especificacionesInstrucciones de funcionamiento Dial Selectora Fijacion Variable Dial SelectoraPortaherramienta SDS DE Cambio Rapido Embrague DeslizanteMantenimiento AccesoriosLimpieza BM 1619929320 2/03 2/12/03 942 AM BM 1619929320 2/03 2/12/03 942 AM Limited Warranty of Bosch Portable and Benchtop Power Tools