Hitachi DH30PB, DH30PC When driving machine screws Fig, When driving wood screws Fig

Page 14
Fig. 9

English

CAUTION:

◯Application of force more than necessary will not only reducing drilling efficiency at all, but will deteriorate the tip edge of the drill bit and reduce the service life of the rotary hammer in addition.

◯Drill bit may snap off while disengaging the rotary hammer from the jammed hole. For disengaging, it is important to use a pushing motion or turn the drill bit counterclockwise.

◯Do not attempt to drill anchor holes or holes in concrete with the main unit in the rotation only function.

◯Do not attempt to use the rotary hammer in the rotation and striking function with the drill chuck and chuck adaptor attached. This would seriously shorten the service life of every components of the machine.

4.When driving machine screws (Fig. 9)

First, insert the bit into the socket in the end of chuck adaptor (D).

Next, mount chuck adaptor (D) on the main unit using procedures described in 6 (1), (2), (3), put the tip of the bit in the slots in the head of the screw, grasp the main unit and tighten the screw.

Bit

Socket

Chuck

 

Adaptor (D)

Front Cap

 

 

Grip

CAUTION:

◯ Exercise care not to excessively prolong driving time, otherwise, the screws may be damaged by excessive force.

◯Apply the rotary hammer perpendicularly to the screw head when driving a screw; otherwise, the screw head or bit will be damaged, or driving force will not be fully transferred to the screw.

◯Do not attempt to use the rotary hammer in the rotation and striking function with chuck adaptor (D) and bit attached.

5.When driving wood screws (Fig. 9)

(1) Selecting a suitable driver bit

Employ phillips screws, if possible, since the driver bit easily slips off the heads of slotted-head screws.

(2) Driving in wood screws

◯ Prior to driving in wood screws, make pilot holes suitable for them in the wooden board. Apply the bit to the screw head grooves and gently drive the screws into the holes.

◯ After rotating the rotary hammer at low speed for a while until a wood screw in partly driven into the wood, squeeze the trigger more strongly to obtain the optimum driving force.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Avertissement AdvertenciaContents Important Safety Information Meanings of Signal WordsSafety General Safety RulesEnglish Never operate without all guards in place Specific Safety Rules and SymbolsNever touch moving parts Use right toolOperate power tools at the rated voltage Blades and accessories must be securely mounted to the toolKeep motor air vent clean Never use a tool which is defective or operating abnormallyMake Them Available to Other Users Owners of this Tool Double Insulation for Safer OperationName of Parts SpecificationsFunctional Description ModelPrior to Operation Assembly and OperationApplications Confirming condition of the environment Installation of dust cup or dustCollector B Optional accessories Mounting the drill bit FigSelecting the driver bit HOW to USESelecting the function mode Rotation only Switch operationRotation + Striking When driving machine screws Fig When driving wood screws FigHandle Bolt Using the stopper FigStriking only DH30PC HOW to USE the Core BIT for Light Load Using the side handleHow to bore Fig Dismounting. FigInspecting the drill bits Maintenance and InspectionMaintenance of the motor Inspecting the screwsHow to replase grease Service and repairsAccessories Standard AccessoriesInner wedge type with the headless screw Knock-in anchor Striking only DH30PCOuter wedge type with the female screw Outer wedge type with Female screw Guide plateGrooving Striking onlyDH30PC Demolishing operation Striking onlyDH30PCGroove digging and edging Striking onlyDH30PC Drilling holes Rotation only Phillips Driver BitDust collector B Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTConserver CES Instructions SecuriteRegles Generale DE Securite Français Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobilesUtiliser l’outil motorisé à la tension nominale Utiliser l’outil correctManipuler l’outil correctement Ne pas essuyer les parties en plastique avec du solvant Double Isolation Pour UN Fonctionnement Plus SUR Modèle Description FonctionnelleNOM DES Parties Poids 10,4 lbs 4,7 kg 10,6 lbs 4,8 kgInterrupteur d’alimentation Avant L’UTILISATIONSource d’alimentation Cordon prolongateurVérification des conditions d’environnement Montage du foret de perçage FigSélection du mode de fonction Sélection de la mèche pour visseuseRotation + frappe UtilisationFonctionnement de l’interrupteur Rotation seulement Lors du vissage des vis machine Fig Enfoncement de vis à bois FigPercussion uniquement DH30PC Utilisation de l’arràtoir FigUtilisation de la poignée latérale MontagePerçage Fig Démontage FigEntretien du moteur Contrôle du foret de perçageInspection des vis Contrôle des balais en carbone FigComment remplacer la graisse Entretien et reparationAccessoires Accessoires StandardType à cale intérieure avec vis sans tête Ancrage de chasse Percussion uniquementDH30PCType à cale extérieure avec vis femelle Plaque centrale de guidage Perçage de trou à large diamètre rotation + frappeGoujon Couronne Travail de démolissage Percussion uniquementDH30PC Creusage de rainures Percussion uniquement DH30PCPerçage de trous rotation seulement Embout de vissage PhillipsCollecteur à poussière B Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónGuarde Estas Instrucciones SeguridadNormas Generales DE Seguridad Español Normas Y Símbolos Específicos DE Seguridad Mantenga limpio el conducto de ventilación del motor No toque Nunca las piezas móvilesManeje correctamente la herramienta Maneje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolventeAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Especificaciones Descripción FuncionalNomenclatura ModeloAntes DE LA Operación Montaje Y OperaciónAplicaciones Confirme las condiciones del medio ambiente Montaje de la broca FigSelección del modo de función Como SE USASelección de la broca destornillador Rotación solamente Operación del conmutadorRotación + golpeteo Español Modo de usar el tope Fig Atornillando tornillos para madera FigPercusión solamente DH30PC Modo DE Usar LA Barrena Tubularpara Cargas Ligeras Uso del asa lateralMontaje Modo de taladrar FigDesmontaje Fig Inspección de los tornillos Mantenimiento E InspecciónInspeccionar la broca de taladro Mantenimiento de motorCambio de grasa Mantenimiento y reparaciónAccesorios Accesorios EstándarTipo de reborde interior con tornillo sin cabeza Ancla de martillar Percusión solamente DH30PCTipo de reborde exterior con tornillo hembra Placa guia Ranurado Percusión solamente DH30PC Trabajo de roturación Percusión solamente DH30PCExcavar, ranuado y rebordes Percusión solamente DH30PC Perforación rotación solamente Broca para tornillos PlillipsColector de polvo B Kestrel Road Mississauga on L5T 1Z5

DH30PC, DH30PB specifications

The Hitachi DH30PB and DH30PC are powerful tools designed to meet the rigorous demands of construction and renovation professionals. Both models are renowned for their performance, ergonomics, and advanced technology, making them ideal choices for a variety of drilling and chiseling applications.

One of the standout features of the DH30PB and DH30PC is their robust motor. Equipped with a high-performance 3.2-amp motor, these tools deliver exceptional drilling power, providing users with the capability to handle tough materials, including concrete, masonry, and more. This powerful motor ensures quick and efficient drilling, saving both time and energy on the job site.

The Hitachi DH30PB and DH30PC also incorporate advanced vibration-reduction technology. This feature minimizes the vibrations transferred to the user's hands during operation, significantly enhancing comfort and reducing fatigue. As a result, professionals can work for extended periods without discomfort, increasing productivity and job satisfaction.

Another impressive aspect of these models is their hammering mechanism. With a high-impact energy rating, the DH30PB and DH30PC offer fast and effective chiseling and hammer drilling capabilities. This versatility makes them suitable for a wide range of applications, from drilling holes for anchors to chiseling through tough surfaces.

In terms of design, both models are built for durability and ease of use. They feature a lightweight construction, making them easy to maneuver in tight spaces while maintaining strength and performance. The rubberized grip enhances comfort and control, ensuring a secure hold during operation.

Moreover, the DH30PB and DH30PC come equipped with a quick-change chuck, allowing for seamless bit changes without requiring additional tools. This feature increases efficiency and convenience on the job site, enabling professionals to switch between tasks effortlessly.

In conclusion, the Hitachi DH30PB and DH30PC models stand out in the crowded market of power tools due to their powerful motors, advanced vibration-reduction technology, and user-friendly design. These features, combined with their exceptional performance in challenging environments, make them reliable companions for professionals in construction, renovation, and various industrial applications. Whether drilling or chiseling, users can count on these tools to deliver results that meet and exceed expectations.
Top Page Image Contents