Hitachi DH30PC, DH30PB instruction manual Switch operation, Rotation + Striking, Rotation only

Page 13

1.Switch operation

The rotation speed of the drill bit can be controlled steplessly by varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the switch is pulled more.

2.Rotation + Striking

This rotary hammer can be set to

rotation and striking mode by pressing the push button and turning the

change lever to mark. (Fig. 5)

(1)Mount the drill bit.

(2)Pull the trigger switch after applying the drill bit tip to the drilling position (Fig. 6)

(3)Pushing the rotary hammer forcibly is not necessary at all. Pushing slightly so that drill dust comes out gradually is just sufficient.

CAUTION:

◯When the drill bit touches an iron reinforcing rod, the bit will stop immediately and the rotary hammer will react to revolve. Therefore please grip the side handle and handle tightly as shown in Fig. 6.

3.Rotation only

This rotary hammer can be set to rotation only mode by pressing the

push button and turning the change

lever to mark. (Fig. 7)

To drill a wood or metal material using the separately sold drill chuck and chuck adaptor, proceed as follows. Installing drill chuck and chuck adaptor (Fig. 8):

(1)Mount the drill chuck to the chuck adaptor.

(2)The part of the SDS-plus shank is the same as the drill bit. Therefore, refer to the item of “Mounting the drill bit” for attaching it.

English

Push

Button

Change

Lever

Fig. 5

Fig. 6

Push Button

Change

Lever

Fig. 7

Front Cap Grip

Drill

Chuck

Chuck

Part of SDS-plus

Adaptor

shank

 

 

Fig. 8

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Advertencia AvertissementContents Meanings of Signal Words Important Safety InformationGeneral Safety Rules SafetyEnglish Never touch moving parts Specific Safety Rules and SymbolsNever operate without all guards in place Use right toolKeep motor air vent clean Blades and accessories must be securely mounted to the toolOperate power tools at the rated voltage Never use a tool which is defective or operating abnormallyDouble Insulation for Safer Operation Make Them Available to Other Users Owners of this ToolFunctional Description SpecificationsName of Parts ModelApplications Assembly and OperationPrior to Operation Collector B Optional accessories Installation of dust cup or dustConfirming condition of the environment Mounting the drill bit FigSelecting the function mode HOW to USESelecting the driver bit Rotation + Striking Switch operationRotation only When driving wood screws Fig When driving machine screws FigStriking only DH30PC Using the stopper FigHandle Bolt Using the side handle HOW to USE the Core BIT for Light LoadDismounting. Fig How to bore FigMaintenance of the motor Maintenance and InspectionInspecting the drill bits Inspecting the screwsService and repairs How to replase greaseStandard Accessories AccessoriesOuter wedge type with the female screw Knock-in anchor Striking only DH30PCInner wedge type with the headless screw Guide plate Outer wedge type with Female screwGroove digging and edging Striking onlyDH30PC Demolishing operation Striking onlyDH30PCGrooving Striking onlyDH30PC Phillips Driver Bit Drilling holes Rotation onlyDust collector B Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéRegles Generale DE Securite SecuriteConserver CES Instructions Français NE Jamais toucher les parties mobiles Regles DE Securite Specifiques ET SymbolesManipuler l’outil correctement Utiliser l’outil correctUtiliser l’outil motorisé à la tension nominale Ne pas essuyer les parties en plastique avec du solvant Double Isolation Pour UN Fonctionnement Plus SUR NOM DES Parties Description FonctionnelleModèle Poids 10,4 lbs 4,7 kg 10,6 lbs 4,8 kgSource d’alimentation Avant L’UTILISATIONInterrupteur d’alimentation Cordon prolongateurMontage du foret de perçage Fig Vérification des conditions d’environnementSélection de la mèche pour visseuse Sélection du mode de fonctionFonctionnement de l’interrupteur UtilisationRotation + frappe Rotation seulement Enfoncement de vis à bois Fig Lors du vissage des vis machine FigUtilisation de l’arràtoir Fig Percussion uniquement DH30PCMontage Utilisation de la poignée latéraleDémontage Fig Perçage FigInspection des vis Contrôle du foret de perçageEntretien du moteur Contrôle des balais en carbone FigEntretien et reparation Comment remplacer la graisseAccessoires Standard AccessoiresType à cale extérieure avec vis femelle Ancrage de chasse Percussion uniquementDH30PCType à cale intérieure avec vis sans tête Goujon Couronne Perçage de trou à large diamètre rotation + frappePlaque centrale de guidage Creusage de rainures Percussion uniquement DH30PC Travail de démolissage Percussion uniquementDH30PCEmbout de vissage Phillips Perçage de trous rotation seulementCollecteur à poussière B Significado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadNormas Generales DE Seguridad SeguridadGuarde Estas Instrucciones Español Normas Y Símbolos Específicos DE Seguridad Maneje correctamente la herramienta No toque Nunca las piezas móvilesMantenga limpio el conducto de ventilación del motor No limpie las partes de plástico con disolvente Maneje con cuidado las herramientas eléctricasAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Nomenclatura Descripción FuncionalEspecificaciones ModeloAplicaciones Montaje Y OperaciónAntes DE LA Operación Montaje de la broca Fig Confirme las condiciones del medio ambienteSelección de la broca destornillador Como SE USASelección del modo de función Rotación + golpeteo Operación del conmutadorRotación solamente Español Percusión solamente DH30PC Atornillando tornillos para madera FigModo de usar el tope Fig Uso del asa lateral Modo DE Usar LA Barrena Tubularpara Cargas LigerasModo de taladrar Fig MontajeDesmontaje Fig Inspeccionar la broca de taladro Mantenimiento E InspecciónInspección de los tornillos Mantenimiento de motorMantenimiento y reparación Cambio de grasaAccesorios Estándar AccesoriosTipo de reborde exterior con tornillo hembra Ancla de martillar Percusión solamente DH30PCTipo de reborde interior con tornillo sin cabeza Placa guia Excavar, ranuado y rebordes Percusión solamente DH30PC Trabajo de roturación Percusión solamente DH30PCRanurado Percusión solamente DH30PC Broca para tornillos Plillips Perforación rotación solamenteColector de polvo B Kestrel Road Mississauga on L5T 1Z5

DH30PC, DH30PB specifications

The Hitachi DH30PB and DH30PC are powerful tools designed to meet the rigorous demands of construction and renovation professionals. Both models are renowned for their performance, ergonomics, and advanced technology, making them ideal choices for a variety of drilling and chiseling applications.

One of the standout features of the DH30PB and DH30PC is their robust motor. Equipped with a high-performance 3.2-amp motor, these tools deliver exceptional drilling power, providing users with the capability to handle tough materials, including concrete, masonry, and more. This powerful motor ensures quick and efficient drilling, saving both time and energy on the job site.

The Hitachi DH30PB and DH30PC also incorporate advanced vibration-reduction technology. This feature minimizes the vibrations transferred to the user's hands during operation, significantly enhancing comfort and reducing fatigue. As a result, professionals can work for extended periods without discomfort, increasing productivity and job satisfaction.

Another impressive aspect of these models is their hammering mechanism. With a high-impact energy rating, the DH30PB and DH30PC offer fast and effective chiseling and hammer drilling capabilities. This versatility makes them suitable for a wide range of applications, from drilling holes for anchors to chiseling through tough surfaces.

In terms of design, both models are built for durability and ease of use. They feature a lightweight construction, making them easy to maneuver in tight spaces while maintaining strength and performance. The rubberized grip enhances comfort and control, ensuring a secure hold during operation.

Moreover, the DH30PB and DH30PC come equipped with a quick-change chuck, allowing for seamless bit changes without requiring additional tools. This feature increases efficiency and convenience on the job site, enabling professionals to switch between tasks effortlessly.

In conclusion, the Hitachi DH30PB and DH30PC models stand out in the crowded market of power tools due to their powerful motors, advanced vibration-reduction technology, and user-friendly design. These features, combined with their exceptional performance in challenging environments, make them reliable companions for professionals in construction, renovation, and various industrial applications. Whether drilling or chiseling, users can count on these tools to deliver results that meet and exceed expectations.
Top Page Image Contents