Hitachi DH30PB, DH30PC HOW to USE, Selecting the driver bit, Selecting the function mode

Page 12

English

(When using dust collector (B) attached to a drill bit that has more than 7-15/ 32" (190 mm) of overall length, dust collector (B) cannot touch the concrete surface but rotates. Therefore please use dust collector (B) by attaching to drill bits which have 6-17/32" (166 mm), 6-19/64" (160 mm) and 4-21/64" (110 mm) overall length.

◯Dump particles after every two or three holes when drilling.

◯Please replace the drill bit after removing dust collector (B).

8.Selecting the driver bit

Screw heads or bits will be damaged should an inappropriate bit for the screw diameter be employed to drive in the screws.

9.Selecting the function mode

You can switch functions to the 3 modes of “strike only, “rotation + strike”, and “rotation only” by turning the change lever while pressing the push button. Set the mark position of the change lever to that of the mode to be used.

CAUTION:

◯Before operating the change lever, check and make sure that the motor has stopped.

A failure can occur if it is operated while the motor is running.

◯If the change lever does not move up to the mark position of each mode, carry out switching while turning the grip end to left and right. Also, it can become difficult to change the mode at low temperature, and therefore perform warming-up.

◯To operate the change lever, press the push button, and release the lock of the change lever. Also, check and make sure after operation that the push button has returned and that the change lever has been locked.

◯Switch the change lever without mistake. If it is used at a position halfway, there is a fear that the service life of the switching mechanism may be shortened.

◯Note that it is impossible to switch from “rotation only” to “strike only” or from “strike only” to “rotation only”. Switch over via “rotation + strike”. (DH30PC)

HOW TO USE

CAUTION:

◯To prevent accidents, make sure to turn the switch off and disconnect the plug from the receptacle when the drill pits and other various parts are installed or removed. The power switch should also be turned off during a work break and after work.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Avertissement AdvertenciaContents Important Safety Information Meanings of Signal WordsSafety General Safety RulesEnglish Specific Safety Rules and Symbols Never touch moving partsNever operate without all guards in place Use right toolBlades and accessories must be securely mounted to the tool Keep motor air vent cleanOperate power tools at the rated voltage Never use a tool which is defective or operating abnormallyMake Them Available to Other Users Owners of this Tool Double Insulation for Safer OperationSpecifications Functional DescriptionName of Parts ModelAssembly and Operation ApplicationsPrior to Operation Installation of dust cup or dust Collector B Optional accessoriesConfirming condition of the environment Mounting the drill bit FigHOW to USE Selecting the function modeSelecting the driver bit Switch operation Rotation + StrikingRotation only When driving machine screws Fig When driving wood screws FigUsing the stopper Fig Striking only DH30PCHandle Bolt HOW to USE the Core BIT for Light Load Using the side handleHow to bore Fig Dismounting. FigMaintenance and Inspection Maintenance of the motorInspecting the drill bits Inspecting the screwsHow to replase grease Service and repairsAccessories Standard AccessoriesKnock-in anchor Striking only DH30PC Outer wedge type with the female screwInner wedge type with the headless screw Outer wedge type with Female screw Guide plateDemolishing operation Striking onlyDH30PC Groove digging and edging Striking onlyDH30PCGrooving Striking onlyDH30PC Drilling holes Rotation only Phillips Driver BitDust collector B Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTSecurite Regles Generale DE SecuriteConserver CES Instructions Français Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobilesUtiliser l’outil correct Manipuler l’outil correctementUtiliser l’outil motorisé à la tension nominale Ne pas essuyer les parties en plastique avec du solvant Double Isolation Pour UN Fonctionnement Plus SUR Description Fonctionnelle NOM DES PartiesModèle Poids 10,4 lbs 4,7 kg 10,6 lbs 4,8 kgAvant L’UTILISATION Source d’alimentationInterrupteur d’alimentation Cordon prolongateurVérification des conditions d’environnement Montage du foret de perçage FigSélection du mode de fonction Sélection de la mèche pour visseuseUtilisation Fonctionnement de l’interrupteurRotation + frappe Rotation seulement Lors du vissage des vis machine Fig Enfoncement de vis à bois FigPercussion uniquement DH30PC Utilisation de l’arràtoir FigUtilisation de la poignée latérale MontagePerçage Fig Démontage FigContrôle du foret de perçage Inspection des visEntretien du moteur Contrôle des balais en carbone FigComment remplacer la graisse Entretien et reparationAccessoires Accessoires StandardAncrage de chasse Percussion uniquementDH30PC Type à cale extérieure avec vis femelleType à cale intérieure avec vis sans tête Perçage de trou à large diamètre rotation + frappe Goujon CouronnePlaque centrale de guidage Travail de démolissage Percussion uniquementDH30PC Creusage de rainures Percussion uniquement DH30PCPerçage de trous rotation seulement Embout de vissage PhillipsCollecteur à poussière B Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónSeguridad Normas Generales DE SeguridadGuarde Estas Instrucciones Español Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móviles Maneje correctamente la herramientaMantenga limpio el conducto de ventilación del motor Maneje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolventeAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Descripción Funcional NomenclaturaEspecificaciones ModeloMontaje Y Operación AplicacionesAntes DE LA Operación Confirme las condiciones del medio ambiente Montaje de la broca FigComo SE USA Selección de la broca destornilladorSelección del modo de función Operación del conmutador Rotación + golpeteoRotación solamente Español Atornillando tornillos para madera Fig Percusión solamente DH30PCModo de usar el tope Fig Modo DE Usar LA Barrena Tubularpara Cargas Ligeras Uso del asa lateralMontaje Modo de taladrar FigDesmontaje Fig Mantenimiento E Inspección Inspeccionar la broca de taladroInspección de los tornillos Mantenimiento de motorCambio de grasa Mantenimiento y reparaciónAccesorios Accesorios EstándarAncla de martillar Percusión solamente DH30PC Tipo de reborde exterior con tornillo hembraTipo de reborde interior con tornillo sin cabeza Placa guia Trabajo de roturación Percusión solamente DH30PC Excavar, ranuado y rebordes Percusión solamente DH30PCRanurado Percusión solamente DH30PC Perforación rotación solamente Broca para tornillos PlillipsColector de polvo B Kestrel Road Mississauga on L5T 1Z5

DH30PC, DH30PB specifications

The Hitachi DH30PB and DH30PC are powerful tools designed to meet the rigorous demands of construction and renovation professionals. Both models are renowned for their performance, ergonomics, and advanced technology, making them ideal choices for a variety of drilling and chiseling applications.

One of the standout features of the DH30PB and DH30PC is their robust motor. Equipped with a high-performance 3.2-amp motor, these tools deliver exceptional drilling power, providing users with the capability to handle tough materials, including concrete, masonry, and more. This powerful motor ensures quick and efficient drilling, saving both time and energy on the job site.

The Hitachi DH30PB and DH30PC also incorporate advanced vibration-reduction technology. This feature minimizes the vibrations transferred to the user's hands during operation, significantly enhancing comfort and reducing fatigue. As a result, professionals can work for extended periods without discomfort, increasing productivity and job satisfaction.

Another impressive aspect of these models is their hammering mechanism. With a high-impact energy rating, the DH30PB and DH30PC offer fast and effective chiseling and hammer drilling capabilities. This versatility makes them suitable for a wide range of applications, from drilling holes for anchors to chiseling through tough surfaces.

In terms of design, both models are built for durability and ease of use. They feature a lightweight construction, making them easy to maneuver in tight spaces while maintaining strength and performance. The rubberized grip enhances comfort and control, ensuring a secure hold during operation.

Moreover, the DH30PB and DH30PC come equipped with a quick-change chuck, allowing for seamless bit changes without requiring additional tools. This feature increases efficiency and convenience on the job site, enabling professionals to switch between tasks effortlessly.

In conclusion, the Hitachi DH30PB and DH30PC models stand out in the crowded market of power tools due to their powerful motors, advanced vibration-reduction technology, and user-friendly design. These features, combined with their exceptional performance in challenging environments, make them reliable companions for professionals in construction, renovation, and various industrial applications. Whether drilling or chiseling, users can count on these tools to deliver results that meet and exceed expectations.
Top Page Image Contents