Hitachi DH 40MR instruction manual Make Them Available to Other Users Owners of this Tool

Page 8

English

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double insulation” means that two physically separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame handled by the operator. Therefore, either the symbol “” or the words “Double insulation” appear on the power tool or on the nameplate.

Although this system has no external grounding, you must still follow the normal electrical safety precautions given in this Instruction Manual, including not using the power tool in wet environments.

To keep the double insulation system effective, follow these precautions:

◯Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this power tool, and only genuine HITACHI replacement parts should be installed.

◯Clean the exterior of the power tool only with a soft cloth moistened with soapy water, and dry thoroughly.

Never use solvents, gasoline or thinners on plastic components; otherwise the plastic may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

8

Image 8

Contents Avertissement AdvertenciaÍndice ContentsTable DES Matieres Important Safety Information Meanings of Signal WordsSafety General Safety Rules English Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Operate power tools at the rated voltageNever use a tool which is defective or operating abnormally Make Them Available to Other Users Owners of this Tool Double Insulation for Safer OperationName of Parts SpecificationsFunctional Description Prior to Operation Assembly and OperationApplications Regulating the number of rotations and hammering Fig HOW to USEHow to drill holes Fig When chipping and shredding at hammering How to chisel or crush FigWhen drilling at rotation + hammering Install the stopper Fig Warming up Fig Using Drill CHUCK, Chuck Adaptor MountingHow to bore Fig Dismounting FigMaintenance and Inspection Maintenance of the motorInspecting the drill bits Inspecting the screwsHow to replase grease Service and repairsEnglish External dia Overall lenght Code No 16 mm 13-3/8 340 mm 19.0 mm English Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTSecurite Regles Generale DE SecuriteConserver CES Instructions Avertissement Lire et coxmprendre toutes les instructionsFrançais Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobilesNe pas essuyer les parties en plastique avec du solvant Garder propres les évents d’air du moteurUtiliser l’outil motorisé à la tension nominale Double Isolation Pour UN Fonctionnement Plus SUR Description Fonctionnelle NOM DES PartiesAvant L’UTILISATION Comment percer des trous Fig UtilisationRéglage du nombre de rotations et de percussion Fig Burinage et découpures en percussion Comment buriner ou broyer FigPerçage en rotation + percussion Installer la quenouille Fig Préchauffage Fig PrecautiónComment Utiliser LA Couronne MontagePerçage Fig Démontage FigEntretien ET Inspection Contrôle du foret de perçageInspection des vis Entretien du moteurComment remplacer la graisse Entretien et reparationFrançais Diamètre extérieur 19,0 mm Remarque Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónSeguridad Normas Generales DE SeguridadGuarde Estas Instrucciones Advertencia Lea y entienda todas las instruccionesEspañol Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móvilesUtilice la herramienta correcta Maneje correctamente la herramientaManeje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolventeAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Especificaciones Descripción FuncionalNomenclatura Antes DE LA Operación Montaje Y OperaciónAplicaciones Modo DE Utilización Montaje de la herramientaRegulación de número de rotaciones e martilleo Fig Taladrar orificios FigForma de picar o romper Fig Cuando taladre con rotación + martilleoPara cortar con escoplo y cincel en el modo de martilleo NOTAFigInstalar el tope Fig Calentamiento Fig Modo DE Usar LA Barrena Tubular MontajeModo de taladrar Fig Desmontaje FigMantenimiento E Inspección Inspeccionar la broca de taladroInspección de los tornillos de montaje Mantenimiento de motorCambio de grasa Mantenimiento y reparaciónEspañol Español Español Español Page Hitachi Koki Canada Co

Related manuals

Manual 26 pages 7.85 Kb