Sanyo PLC-XP55L owner manual Basic Operation, Turning on / OFF Projector, Turning on Projector

Page 20

BASIC OPERATION

TURNING ON / OFF PROJECTOR

TURNING ON PROJECTOR

1

Complete peripheral connections (with Computer, VCR, etc.)

before turning on projector. (Refer to "CONNECTING TO

 

PROJECTOR" on pages 12~14 for connecting that equipment.)

2

Connect a projector's AC Power Cord into an AC outlet. LAMP

Indicator lights RED, and READY Indicator lights GREEN.

 

NOTE : When “On start” function is ON, this projector is turned

 

on automatically by connecting AC Power Cord to an

 

AC outlet. (Refer to page 39.)

3

Press POWER ON-OFF button on Top Control or on Remote

Control Unit to ON. LAMP Indicator dims, and Cooling Fans

start to operate. Preparation Display appears on a screen and count-down starts. Signal from PC or Video source appears after 30 seconds.

Current Input position and Lamp mode status are also displayed on screen for 5 seconds. (Refer to "LAMP MODE" on page 37.)

Input position and

Lamp mode status

30

Preparation Display disappears after 30 seconds.

 

TURNING OFF PROJECTOR

1

Press POWER ON-OFF button on Top Control or on Remote

 

Control Unit, and a message "Power off?" appears on a screen.

 

2

Press POWER ON-OFF button again to turn off projector. LAMP

 

Indicator lights bright and READY Indicator turns off. After

 

 

projector is turned off, Cooling Fans operate (for 90 seconds).

Message disappears after 4 seconds.

 

During this "Cooling Down" period, projector cannot be turned

 

 

 

on.

 

3

When projector has cooled down, READY Indicator lights

 

GREEN again and you can turn projector on. After cooling down

 

completely, disconnect AC Power Cord.

TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN

PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE

TURNING IT OFF.

When “Power Management” function mode is Ready or Shut down, projector detects signal interruption and turns off the Projection Lamp automatically. Refer to “Power management” on page 39.

When WARNING TEMP. Indicator is flashing, projector cannot be turned on, refer to the section "MAINTENANCE" on page 42. When the both WARNING TEMP. and READY Indicator flashing, refer to the section "MAINTENANCE" on page 42.

Do not use the projector continuously for 24 hours or more. If using the projector continuously for long periods, turn it off and leave it for one hour at least once during a 24 hour period.

If you use the projector continuously for long period, it can excessively shorten the life of the lamp.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model PLC-XP55 To the Owner Safety Instructions Voor de klanten in NederlandCompliances Plummer Street, Chatsworth, CaliforniaTable of Contents Features and Design Compact Design Digital Zoom for ComputerHOT AIR Exhausted PreparationName of Each Part of Projector For Continental Europe For the U.K SETTING-UP ProjectorConnecting AC Power Cord Preparation Positioning Projector Room LightPreparation Adjustable Feet Installing Projector in Proper PositionPreparation Moving Projector Connecting Projector Terminals of ProjectorConnect computer output Digital DVI-D type to this terminal Refer to P13A Projector Connecting to ComputerTerminals Connecting to Video Equipment Operation of Remote Control Inside the Battery Compartment BOXBefore Operation Laser Pointer FunctionRemove battery Compartment lidSlide batteries into CompartmentTOP Controls and Indicators Flow of ON-SCREEN Menu Operation HOW to Operate ON-SCREEN MenuOperating ON-SCREEN Menu Press Menu Button while connecting to PC input source Used to adjust picture imageBefore Operation Menu BAR Used to selectBasic Operation Turning on / OFF ProjectorTurning on Projector Turning OFF ProjectorAdjusting Screen Keystone AdjustmentFocus adjustment may not function properly if the image is Corrected by Keystone adjustmentSound Adjustment Computer Input Selecting Input SourceSelecting Computer System Rgbav HdcpPC System Menu Automatic MULTI-SCAN SystemAuto PC Adjustment Auto PC AdjustmentPC Adjust Menu Auto PC AdjComputer Input Manual PC Adjustment Full screen Display areaDisplay area H Picture Image Select Image Level Select DirectImage Level Select Menu Image Select MenuPicture Screen Adjustment Screen MenuWhen video input signal is connected to Video jack Video InputVideo Select VideoSelecting Video System AutoAV System Menu Video or S-VIDEO AV System Menu Component VideoPicture level adjusted for picture with fine tone CinemaProvides image at a normal video aspect ratio of 4 Provides image at a wide screen ratio of 16Picture Image Picture Image AdjustmentsImage Adjust Menu List Mode Picture ImageColor temp White balance RedWhite balance Green White balance BlueSetting Menu SettingSetting Menu Anamorphic Blue backDisplay Menu positionTo change the code of the Remote Control Unit Power managementRemote control To change the code of ProjectorWireless Mouse mode Projector modeLamp counter reset Factory defaultOperating Wireless Mouse InstallationOperating Wireless Mouse AppendixStation MaintenanceIndicatorIndicator Appendix AIR Filter Care and Cleaning Cleaning Projection LensRecommendation Pull up and removeLamp Replacement Lamp ReplaceMessage Lamp replace counter reset? is displayed. Move Reset Lamp Replace CounterAppendix Lamp Replace Counter Pointer to Yes and then press Select buttonTroubleshooting Service Appendix Indicators and Projector Condition Appendix Compatible Computer Specifications ResolutionMenu Tree PC sourceSystem Setting Sound Technical Specifications Appendix Configurations of Terminals Control Port ConnectorUSB Connector Series B Computer INPUT-1 and Monitor OUT Terminals AnalogLens Replacement Appendix Optional PartsAppendix Part No 306 0675 1AA6P1P3948-- MR3A
Top Page Image Contents