Sanyo PLC-XP55L owner manual Picture Image Adjustments, Image Adjust Menu

Page 34

PICTURE IMAGE

PICTURE IMAGE ADJUSTMENTS

1

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT buttons to move a red frame pointer to

 

IMAGE ADJUST Menu icon.

2

Press POINT UP/DOWN button to move a red frame pointer to

item that you want to adjust and then press SELECT button.

Level of each item is displayed. Adjust each level by pressing POINT LEFT/RIGHT button(s).

Contrast

Press POINT LEFT button to decrease contrast, and POINT RIGHT button to increase contrast. (From 0 to 63.)

Brightness

Press POINT LEFT button to adjust image darker, and POINT RIGHT button to adjust brighter. (From 0 to 63.)

Color

Press POINT LEFT button to lighten color, and POINT RIGHT button to deeper color. (From 0 to 63.)

Tint

Press POINT LEFT button or POINT RIGHT button to obtain proper color. (From 0 to 63.)

Color Management

The Color management function can be used to adjust the level, phase and gamma of the selected display colors on the screen, and to replace these colors with other colors if required.

The projector lets you replace up to eight colors for each image. There are four preset images for VIDEO mode and four preset images for PC, giving a total of eight images.

1

Press the POINT UP/DOWN button to move the red frame point-

er to "COLOR MANAGEMENT", and then press the SELECT

 

button. The COLOR MANAGEMENT menu will appear and

 

pointer mode will be enabled. The image that was being project-

 

ed when the button was pressed will be paused, and the COLOR

 

MANAGEMENT POINTER will appear.

2

Use the POINT buttons to move the pointer to a section of the

paused image that contains the color that you would like to

 

adjust, and then press the SELECT button. The mode will

 

change to COLOR SELECTION mode, and the color in the cen-

 

ter of the pointer will be selected and adjustment will be possi-

 

ble.

3

Use the POINT buttons to adjust the level and phase of the

color, and then press the SELECT button to confirm the setting.

Next, use the POINT buttons to adjust the gamma correction for the color, and then press the SELECT button to accept the set- ting. When the SELECT button is pressed, the mode will change to LIST mode.

IMAGE ADJUST MENU

IMAGE ADJUST

Menu icon

Move a red frame pointer to item to be selected and then press SELECT button.

Press POINT LEFT/RIGHT buttons to adjust value.

POINTER MODE

COLOR

MANAGEMENT

POINTER

NOTE;

Press the COLOR M. button on the remote con- trol to display the COLOR MANAGEMENT menu. If you would like to check or re-adjust a color management setting that has already been made, press the COLOR M. button on the remote control once more to change to LIST mode.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Model PLC-XP55 To the Owner Safety Instructions Voor de klanten in NederlandCompliances Plummer Street, Chatsworth, CaliforniaTable of Contents Features and Design Compact Design Digital Zoom for ComputerName of Each Part of Projector PreparationHOT AIR Exhausted Connecting AC Power Cord SETTING-UP ProjectorFor Continental Europe For the U.K Preparation Positioning Projector Room LightPreparation Adjustable Feet Installing Projector in Proper PositionPreparation Moving Projector Connect computer output Digital DVI-D type to this terminal Connecting ProjectorTerminals of Projector Refer to P13Terminals Connecting to ComputerA Projector Connecting to Video Equipment Before Operation Operation of Remote ControlInside the Battery Compartment BOX Laser Pointer FunctionSlide batteries into Remove batteryCompartment lid CompartmentTOP Controls and Indicators Operating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Press Menu Button while connecting to PC input sourceUsed to adjust picture image Used to selectTurning on Projector Basic OperationTurning on / OFF Projector Turning OFF ProjectorFocus adjustment may not function properly if the image is Adjusting ScreenKeystone Adjustment Corrected by Keystone adjustmentSound Adjustment Selecting Computer System Computer InputSelecting Input Source Rgbav HdcpAuto Automatic MULTI-SCAN SystemPC System Menu PC Adjust Menu PC AdjustmentAuto PC Adjustment Auto PC AdjComputer Input Manual PC Adjustment Display area H Display areaFull screen Image Level Select Menu Picture Image SelectImage Level Select Direct Image Select MenuPicture Screen Adjustment Screen MenuVideo When video input signal is connected to Video jackVideo Input Select VideoAV System Menu Video or S-VIDEO Selecting Video SystemAuto AV System Menu Component VideoPicture level adjusted for picture with fine tone CinemaProvides image at a normal video aspect ratio of 4 Provides image at a wide screen ratio of 16Image Adjust Menu Picture Image AdjustmentsPicture Image List Mode Picture ImageWhite balance Green Color tempWhite balance Red White balance BlueSetting Menu SettingSetting Menu Display AnamorphicBlue back Menu positionRemote control To change the code of the Remote Control UnitPower management To change the code of ProjectorLamp counter reset Wireless Mouse modeProjector mode Factory defaultOperating Wireless Mouse Operating Wireless MouseInstallation AppendixIndicatorIndicator MaintenanceStation Recommendation Appendix AIR Filter Care and CleaningCleaning Projection Lens Pull up and removeLamp Replacement Lamp ReplaceAppendix Lamp Replace Counter Message Lamp replace counter reset? is displayed. MoveReset Lamp Replace Counter Pointer to Yes and then press Select buttonTroubleshooting Service Appendix Indicators and Projector Condition Appendix Compatible Computer Specifications ResolutionMenu Tree PC sourceSystem Setting Sound Technical Specifications USB Connector Series B Appendix Configurations of TerminalsControl Port Connector Computer INPUT-1 and Monitor OUT Terminals AnalogLens Replacement Appendix Optional PartsAppendix Part No 306 0675 1AA6P1P3948-- MR3A
Top Page Image Contents